D-305640 SR-720B PG2 Installation Instructions
3
4
4
4
4.
.
.
. CONFIGURING THE SIREN PARAMETERS
CONFIGURING THE SIREN PARAMETERS
CONFIGURING THE SIREN PARAMETERS
CONFIGURING THE SIREN PARAMETERS
Enter the
DEV SETTINGS
menu and follow the configuration instructions for the SR-720B PG2 indoor siren as described below.
Option
Configuration Instructions
STROBE ALARM
Define whether or not to activate the strobe alarm, and if activated, whether to activate the strobe until the alarm
system is disarmed, or, for the programmed period of time (see the "Siren Configuration" section in the control
panel Installer Guide).
Optional settings:
Timer limited
(default),
Disabled
and
Until Disarmed
.
EXIT-ENTRY Beeps
Define whether or not to activate the exit – entry beeps, and if activated, whether to activate in HOME or AWAY mode.
Optional settings:
Disabled
(default),
Disabled & Home
and
Enabled
.
SQUAWK
Define whether or not to enable the squawk, and if enabled, whether to activate the sounder only, or, the sounder and
strobe simultaneously.
Optional settings:
Disabled
(default),
Sounder only
,
Strobe only
and
strobe
.
SOUNDER VOLUME
Define the volume level of the sounder.
Optional settings:
Volume HIGH
(default),
Volume LOW
and
Volume MID
.
AUTO TAMPER ALRM
Define whether or not the siren alone will sound a tamper alarm when there is no communication between the siren
and the control panel.
Optional settings:
Disabled
(default) and
Enabled
.
5
5
5
5.
.
.
. LOCAL DIAGNOSTICS TEST
LOCAL DIAGNOSTICS TEST
LOCAL DIAGNOSTICS TEST
LOCAL DIAGNOSTICS TEST
Before testing, remove the plastic cover and then open the
battery cover (see Fig. 2).
A.
Press the self-test button (see Fig. 3) once and release it; the
following procedure should occur in turn:
The red LED will switch ON and then OFF, the green LED will
switch ON and then OFF, the strobe light will switch ON and
then OFF and the piezo siren will sound to indicate that the
siren is now fully operational.
B.
After 2 seconds the LED blinks 3 times.
The following table indicates received signal strength
indication.
LED response
Reception
Green LED blinks
Strong
Orange LED blinks
Good
Red LED blinks
Poor
No blinks
No communication
IMPORTANT!
Reliable reception must be assured. Therefore,
"poor" signal strength is not acceptable. If you receive a "poor"
signal from the device, re-locate it and re-test until a "good" or
"strong" signal strength is received.
For detailed Diagnostics Test instructions refer to the control
panel Installer Guide.
Note:
For UL/CUL installations, the test result must be “Strong”.
6
6
6
6.
.
.
. COMPLIANCE WITH STANDARDS
COMPLIANCE WITH STANDARDS
COMPLIANCE WITH STANDARDS
COMPLIANCE WITH STANDARDS
Compliance with Standards
Europe:
EN 301489, EN 50130-4, EN 50130-5, EN 50131-4 Type W, EN 300 220, EN 60950-1
Security Grade 2, Environmental Class II.
UK:
This product is suitable for use in systems installed to conform to PD6662:2010 at Grade 2 and
environmental class 2. DD243 and BS8243
The SR-720B PG2 is compatible with the RTTE requirements - Directive 1999/5/EC of the European
Parliament and of the Council of 9 March 1999.
USA:
CFR 47 Part 15 (FCC)
Canada:
RSS 210
Certified by Applica T&C.
The Power G peripheral devices have two- way communication functionality, providing additional benefits as described in
the technical brochure. This functionality has not been tested to comply with the respective technical requirements and
should therefore be considered outside the scope of the product’s certification.
The digital circuit of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
Note:
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such
modifications could void the user's authority to operate the equipment.