Infant Protection Bracelet – User Guide ___________________________________________________________________________________________
Page 3 of 4
BTC03U01
Specifications
Electrical
Radio Transmission Rates:
▪
IR: In-motion / Motionless / While Charging
▪
RF: In-motion / Motionless / While Charging
Every 7.5 seconds / 15 seconds / 120 seconds
Supervision message every 15 seconds/15 seconds/120 seconds,
each lasting @ 2ms.
RF Transmission Rate
upon entry into LF area
Burst of 4 messages (each lasting @ 2ms), with intervals of 400ms
Tamper Transmission Rate
Burst of 4 messages (each lasting @ 2ms), with intervals of 400ms
Electrical Power Source
One Lithium Ion rechargeable battery pack
Battery Life
Approximately 1 week between recharges
Status Indications
Low battery condition: Pulsating red LED
RF and IR transmissions: Pulsating green LED
Badge ID code
Unique factory programmed ID
General
Construction
Polymer plastic
Physical Dimensions
39.4 X 31.5 X 14.8 mm (1.55 x 1.24 x 0.582 inches)
Weight (assembled)
20 grams (0.75 ounces) approximate
Temperature & Humidity
Temp: -10°C to 70°C (14°F to 158°F), Humidity: 20% to 80% non-condensing
Tag Housing
IP66 water rated enclosure
Bracelet Configuration
IP55 water rated configuration
Warranty
One year limited warranty (excluding battery)
Compliance Standards
EN 300 220-3, EN301 489-03, EN50130-4:95+A1(98) +A2(03), EN60950-1:01,
EN 60601-1/2,FCC Part 15.231 Level C, FCC ID#: GSA-BTC00433 (433.92 MHz)
Ordering Details 5-BTC09433
Part Information
5-BTC00433-A
Rechargeable Tag, IR/RF/LF. 433MHz, 7.5/15/60
5-BTC00433
Pack of 10 Rechargeable Tags, includes 2 extractors
5-BTC09433
Dummy Rechargeable Tag
Accessories
5-CRG90001
Charger, 6 position, European standard
5-CRG90001-1
Charger, 6 position, US standard
5-CRG90001-2
Charger, 6 position, UK standard
5-BTC90001-1
Disposable Tamper Band, Pediatric,
24cm maximum diameter, (25 units)
5-BTC90001
Disposable Tamper Band, Infant,
16cm maximum diameter, (50 units)
5-BTC90003
Extractor, Infant (10 units)
5-BTC90006
Grip key w/lanyard (set of 5)
Standards Compliance
This device complies with Part 15 of the FCC Rules; and its operation is subject to
the following two conditions:
•
This device may not cause harmful interference
•
This device must accept any interference received, including interference
that may cause undesired operation.
For a Class B digital device or peripheral, the instructions furnished the user shall
include the following or similar statement, placed in a prominent location in the
text of the manual:
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Warning!
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance (Visonic Technologies Ltd.) could void the user’s
authority to operate the equipment.