Vislink DXL5000 RX Скачать руководство пользователя страница 22

Страница: 22 / 40

3-4 Operating the DXL5000

DXL5000 User and Technical Manual

3.2.5

Status–Firmware Revisions

The

Firmware Revision

screen displays identifying information for the DXL5000. Have this

information ready for customer service as described in

Section 1.3,

Getting Support for Your

DXL5000

on page 1-6.

3.2.6

Status–Monitor Monitor Mod (Transmitter) and Demod (Receiver)

The

Monitor Mod and Monitor Demod

screens displays the following information.

System Software

SCM PC FPGA (single carrier modulator PC field programmable gate array)

SCM PC uP (single carrier modulator PC microprocessor)

SCD PC FPGA (single carrier demodulator PC field programmable gate array)

SCD PC uP (single carrier demodulator PC microprocessor)

Radio Type

Symbol Rate

Displays 3.0 to 33 mega-symbols per second (Msps).

Modulation

Displays the modulation type (

QPSK

16QAM

32QAM

64QAM

Percent
Utilization

Displays a capacity value based on calculations derived from the

Symbol Rate

Modulation

, and the combined

Data Rates

for each

Core Channel

. If this

number is over 100%, you should adjust the values described in

Section 3.3.5,

Determining Optimal System Utilization

on page 3-8.

Core Channel
1, 2, 3, and 4

Displays one of the following the data inputs or outputs and its speed at
megabits per second (Mbps).

ASI BNC-1
ASI BNC-2
ASI BNC-3
E3 BNC-1
ASI BNC-1

DS3 BNC-1
DS3 BNC-2
DS3 BNC-3
E3 BNC-2
DS3 BNC-1

E1RJ45-1
E1RJ45-2
T1RJ45-1
T1RJ45-2
E1RJ45-1

Ethernet RJ45-1
RS232
RS485
SMPTE BNC-3
Ethernet RJ45-1

Invert
Spectrum

Displays

Off

for the Invert Spectrum.

PRBS

Displays

Off

(default) for the Pseudo Random Bit Sequence (PRBS).

PRBS is used for link testing purposes; turning PRBS

causes a data service

override.

The following fields apply only to the receiver.

SNR

Displays the number of dB for the signal-to-noise ratio (SNR) that measures the
signal strength and signal quality.

EVM

Displays a percentage of the error vector magnitude (EVM) that measures the
performance of the radio.

BER

Active only when the transmitter has PRBS

, BER displays the bit error ratio

(BER), which is the percentage of bits that have errors relative to the total
number of bits in the signal, and indicates how often a packet or data unit has to
be retransmitted because of an error. You can click

Reset BER

to start a new

ratio.

Содержание DXL5000 RX









































Результаты поиска

Содержание DXL5000 RX

Отзывы:

Похожие инструкции для DXL5000 RX

Бренды по названию

Популярные бренды

Vislink DXL5000 RX, Руководство пользователя и техническое руководство

Результаты поиска

Содержание DXL5000 RX

Отзывы:

Похожие инструкции для DXL5000 RX

Бренды по названию

Популярные бренды