VISIONARY DESIGNS RE-2070 Скачать руководство пользователя страница 6

© 2017

Step 2 of 6

Closet Assembly (cont’d)

ABOVE-DOOR

INFILL

DOOR
INFILL

When assembled

Steps:
1) Attach lower horizontal [7] between vertical [1] & [2];
    slide 

SIDE INFILL 

between verticals & secure with upper horizontal [7A].

2) Install Door Threshold between verticals [5,6].

See 

Door Threshold Attachment 

detail.

3) Connect horizontal [11] between verticals [5,6]; slide

ABOVE DOOR INFILL 

between verticals & secure with

upper horizontal [11A].

4) Attach vertical [13] between horizontals [12,12A].
5) Install 

Door 

with 

DOOR INFILL

 between verticals [5,6].

See 

Door Attachment

 detail.

6) Apply 

SEG Graphics [A], [B] & [C]

 to front frames as shown.

Attach SEG Blocker to back of assembly.

Item

7/7A

11/11A

13

--

Qty.

1/1
1/1

1
1

Description
28“w Z45 Horizontal Extrusion
28“w Z45 Horizontal Extrusion
88.417”h Z33 Vertical Extrusion
Door Threshold

Door
Hinge

Hinge

Slide pin into
hinge attached
to vertical. 
Slide door
hinge over pin.

Door Attachment

*

Pin

Door Threshold

Tighten 
setscrew
to secure

Slide Connector

into Groove

of Extrusion

Door Threshold

Attachment

*

7A

1

6

12A

12

5

2

11A

13

7

11

*

*

*

SIDE INFI

LL

SEG Graphic Installation

Corner A

Corner D

Corner B

Corner C

It is important to first insert
graphic into each alternate
corner then to the sides of
the frame.  If this is not done,
graphic will not fit into the
frame correctly.

Step 1
Insert corner A.  Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic.  Insert narrow side
of welt with fabric to outside
into the channel.  Repeat for
other side of this corner.

Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.

Graphic Removal

To remove the graphic from
the frame, locate the fabric
pull tab.  Gently pull up on
the tab to remove the fabric.

Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel.  Continue until
all sides are done.  Smooth
out edges of graphic.

SE

G G

raph

ic

SEG

Graph

ic

SEG Gra

phic

SEG

 Blocke

r

A

B

C

Door

Содержание RE-2070











Отзывы: