Please lock the dome with the lever strong enough after adjustments so that the camera’s
angle withstands its direction firmly against vibration or external shock.
2. Video Monitor
Connect Video cable with BNC-male connector to the monitor.
3. Power
Before sending the camera out for repair, check the items below. If the camera
persists after checking these items, contact your service center.
*Specifications are subject to change without prior notice.
Please check the power connection.
Please check the video signal line connection.
Nothing appears on
the screen.
The video image is
not clear.
The screen is dark.
The camera’s surface
is too hot and black
stripes appear on the
screen.
The screen is flickering.
IR beam is weak
Please check if the lens or the outer glass is clean.
- Dirt or fingerprints on the lens can affect the image blooming or
reflection. Gently wipe any dirt or fingerprints off the lens or the
glass with a soft cloth.
Please check and adjust contrast feature of the monitor
Please check if the camera is exposed directly toward a bright light,
sunlight, or sun light reflecting area.
Please move the camera’s position in this case.
Please check and adjust contrast feature of the monitor
If there is any interim equipment, set the 75
position properly and
check the terminals.
Please check if the power supply is within the specification.
- When the cable connection requires a long distance, there
may need a higher power supply or an additional power/video
amplification.
Please check if the power supply is regulated and is within the
standard requirement of the product.
Please check if the camera is facing directly toward sunlight or
fluorescent light.
Check if the distance of the cable installation is too long or if the
cable is not UL standard. Using a lower grade cable or long distance
cable installation can cause a serious voltage drop. Please check
the voltage output level of the cable and change the power source in
this case. Make a special care not to supply too much power over
the camera as well.
12VDC
200
mA
1/3 Sony Super HAD CCD (option : 1/3” Sony Ex-view HAD CCD)
NTSC : 512(H) X 492(V)
768(H) X 494(V)
PAL : 500(H) X 582(V)
752(H) X 582(V)
2:1 Interlace
Internal
NTSC : 400TVL (C) / 420TVL (B) NTSC : 500TVL (C) / 560TVL (B)
PAL : 380TVL (C) / 400TVL (B) PAL : 480TVL (C) / 540TVL (B)
1.0Vp-p
50 dB (AGC Off)
0.2Lux / F2.0 (IR Off) (option : 0.1 Lux / F2.0 (IR off))
0 Lux / F2.0 (IR On)
Auto
Auto
1/60 (NTSC) ~ 1/120,000 per sec.
1/50 (PAL) ~ 1/100,000 per sec.
IR corrective 3.6mm / F2.0 - Standard
4.3mm, 6mm, 8mm - Optionable
Color at day and Real B/W image at night
850nm-30 IR x 14ea - Standard
940nm-30 IR x 14ea - Option
IP6
6
- 20 C ~ +50 C (- 4 F ~ +122 F)
- 40 C ~ +70 C (- 40 F ~ +158 F)
79 x 64 mm (
3.11 x 2.52 )
Approx. 300g
Power
CCD
SYNC
Electrical
Lens
Day/Night
Environ-
mental
Physical
ITEM
VD70CS
(X)
-36I
R
VD70CSHR
(X)
-36IR
Input voltage
Operating current
Sensor
Effective Pixels
Scanning system
Synchronization
Rosolution
(C: Color / B: B/W)
Video output
S/N Ratio
Min.illumination
Gain control
White balance
Shutter speed
Monofocal
Image conversion
Infra-red
Weatherproof
Operating temp.
Storage temp.
Dimension
Weight
Please make sure that the surface
of the lens and the dome cover
always stay clear.
When these parts are
contaminated, clean them very
carefully with soft cloth.
Even a small scratch on these
parts results in the picture blooming
or reflection.
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Caution!
Impedance alliance in the system connection.
Make sure to connect the cable with the power off.
Please locate the impedance switch of each equipment as instructed.
Locate the switch to Hi-z position for the interim equipments.
Locate the switch to 75
for the last equipment.
12VDC
Please make sure to use a UL/CE
approved and 12VDC regulated
power supply.
<Waterproof Cable Option>
Trouble shooting
Specification