STEP 4a
SET-UP
STEP 5
Step 4: Grill Assembly
• Take all parts out of grill before lifting. The grill is
heavy and will require two people to lift and guide
the Kamado into cart.
• Be sure the Ash Drawer is centered between the two
front legs and the grill is resting against the two back
legs.
• Lower fire bowl into grill with the ash drawer opening
lined up with the opening in the main ceramic body.
Place cast iron charcoal grate with attached starter
pocket into fire bowl
(Step 4a)
. Align tabs of starter
pocket with electric starter port in fire bowl.
STEP 6a
Step 6: Ash Drawer Usage
• Once grill is cool, it is safe to remove ash from ash
drawer.
• Using bottom knob on Ash Drawer, lift slightly
(Step 6a)
and pull drawer out
(Step 6b)
.
• Once ash is emptied, reinstall by pushing Ash Drawer
back into grill body until it drops down back into place.
Step 5:
Lava Stone &
Bracket Assembly
• Open grill and take off grill grates to expose fire
bowl.
• Spread bracket so it makes an “X” shape and
lower onto fire bowl, allowing the bracket to rest
on edge of bowl.
• Lower Lava Stone onto the bracket.
STEP 6b
STEP 4b
Step 7: KamadoMatic™
Hinge Adjusting
STEP 7
WARNING:
PERFORMING MANUAL
ADJUSTMENTS TO THE HINGE CAN
CAUSE UNEXPECTED MALFUNCTION
OR DAMAGE IF THESE STEPS ARE
NOT FOLLOWED CORRECTLY.
The KamadoMatic™ Hinge on your Pro Kamado
is already pre-adjusted for ideal balance and
stability. Follow these instructions to manually
adjust the hinge further to your preference.
CAUTION:
KamadoMatic™ Hinge under high tension.
• Open the dome of your Pro Kamado.
• While holding the top dome open with one
hand, use the provided 13mm wrench to
adjust the Spring Nut as shown in (Step 8).
• If the top dome jumps up too quickly upon
opening, turn the Spring Nut
Counter
Clockwise
to loosen the spring and reduce
tension. Turn the Spring Nut for two turns at
a time and test the lid for your preference. The Spring Nut can also be turned
Clockwise
to tighten the spring and add tension, if necessary.
NOTE:
Depending on the amount of resistance and tightness of seal it may be
necessary to use a small amount of force to lock the lid and have the lock handle
slide into the latch. Be careful not to slam the top lid shut.
If the Lid is not staying open during operating
the grill and it is too hot to reach in and adjust
the Spring you can use the Rotation Set Screw
located on the rear of the KamadoMatic
TM
Hinge Housing.
Open the ceramic lid all the way to the top, and
then tighten the Rotation Set Screw by turning it
clockwise until you reach your desired tension.
This will conveniently allow you to adjust the lid
tension until it is safe to adjust the Spring.
Rotation Set Screw Adjustment
Important Notice and Reminder:
This Rotation Set Screw adjustment is a
temporary solution.
When you are done grilling and the grill cools
down, loosen the Rotation Set Screw, and
proceed to the Hinge adjustments detailed in
Step 7
.
Step 3: Handle and Side Shelves
Step 3a
:
• Remove nuts and washers from bolts welded
on the top banding opposite the hinge.
• Remove paper washers and attach handle
bracket over studs. On each stud place a flat
washer and an acorn nut, then tighten .
ÉTAPE 2
STEP 3b
• Remove bolts, washers and locking washers from the
three “X” connectors.
• Remove paper washers and begin assembling the “X”
connectors and legs.
• Please Note: Top, Middle & Bottom “X” connectors
must be assembled simultaneously.
• Assemble cart by inserting the three “X” connectors
into leg ends and install bolts and washers in the
same order they were removed from “X” connectors.
• While assembling, only finger-tighten bolts to allow
for adjustment in cart. Otherwise it can be difficult to get all the bolts inserted.
• Screw in Standard Rubber Wheels to rear Cart Legs and the Locking Rubber
Wheels to the front Cart Legs.
• Once Cart is assembled, flip cart over so that bolts are exposed.
Step 1: Cart Assembly
Step 2: Electric Starter Holster
Step 2a
:
• Loosen the (4) outer bolts slightly so as to allow for the Holster body to slide into
the gap between the bolt heads and the leg bars.
Step 2b
:
• With opening of Holster facing the front of the cart (the Locking Wheels) slide
toward the rear of the cart. Then slide the holster back into place.
Step 2c
:
• Using provided T-Handle Wrench, tighten bolts again through hole openings in
bottom of Holster.
•Once Holster is secure, flip cart back over to proper position so that it is resting on
Wheels. Continue Grill Assembly.
STEP 2c
STEP 2b
STEP 1
Shown here is the bottom of the cart,
flipped upside down
STEP 2a
STEP 3a
Step 3b
:
• Remove the nuts and washers from the bolts
welded on the bottom banding carefully.
Remove the paper washers.
• Place the side brackets on the bolts
and screw side brackets down tightly
with the nuts and washers. Mount shelf
brackets over studs on the sides of the
metal bands on the bottom ceramic
grill body with bracket slots facing up.
Brackets are stamped on the back with
letters indicating their position (e.g.,
LF=Left Front bracket and RB=Right
Back bracket).
• Mount a flat washer then acorn nut on
each stud and tighten with provided wrench.
• Mount side shelves by inserting the shelf rod into the shelf bracket. Tilting the
shelf up slightly and sliding in or out allows you to deploy or store the shelves.
WARNING: ALWAYS WAIT FOR ASH TO COOL
BEFORE REMOVING ASH DRAWER.
NEVER PULL OUT ASH DRAWER
WHILE GRILL IS HOT.
www.visiongrills.com
Vision Grills 1531 Fairview Avenue, Suite B,
St. Louis, MO 63132
1-877-917-4273
• Place cooking grates onto
grill with hinged section
facing towards front of
grill.
• Close lid and press
top vent onto grill with
calibrations facing the front
(Step 4b)
.
ATTENTION:
THE KAMADOMATIC
TM
HINGE WILL CAUSE THE TOP
LID TO JUMP SLIGHTLY WHEN PULLING ON THE LATCH BUTTON.
