Always wait for grill to completely cool before opening built-in ash drawer.
When charcoal cooking above 500º F/260º C, with both top and bottom vents closed, rapidly opening the lid creates a sudden rush of oxygen into the grill,
which can cause a flare-up of flames. When in this cooking mode, we recommend that, prior to opening the lid, you open both top and bottom vents to allow
oxygen to stabilize inside the grill, minimizing the possibility of flare-ups.
WARNING
• Place the Gas Tank Caddy between
the rear legs of the grill cart (Step 1a).
• Fasten mounting brackets to cart
by removing nut and bolt from each
bracket, separating the top bracket
piece from Gas Tank Caddy frame.
Step 1: Install Gas Caddy to Grill Cart
• Slide Gas Tank Caddy under Cart, so top
bracket piece rests on cart frame and is
lined up with bolt hole on bottom of Gas
Tank Caddy.
• Reinsert bolt into frame and tighten
together with nut (Step 1b).
• Use the provided wrench to tighten all
connections.
• Attach the two hose brackets (used to hold
gas hose), with eyelets facing in, onto the
front and rear legs of cart (Step 2).
• Put the gas tank on the Gas Tank Caddy
and tighten into place using Gas Tank Caddy
knob (Step 3a).
STEP 1a
STEP 1b
STEP 2
• When connecting regulator
assembly to the valve, hand
tighten the quick coupling nut
clockwise to a complete stop
(Step 3b).
• After the gas hose is connected to
the gas tank and Gas Insert, open
valve on gas tanks and perform
some type of leak test* method to
test the connection.
STEP 3b
STEP 3a
• From rear of the grill, feed gas hose through
eyelets of the hose brackets, grill connector first.
Connect gas hose to the Gas Insert using the
Quick Disconnect fitting.
• Make sure the cylinder valve is closed (turn valve
clockwise until tight).
• Inspect valve connections, port, hose and
regulator assembly for any damage or debris.
Remove any debris.
Step 2: Attach Hose Brackets
Step 3: Install Gas Tank
Note: Do NOT allow the hose to touch the ceramic.
WARNING: To avoid shock, do not touch spark on burner.
• Remove Ignition Button Cap by turning
counter clockwise. Insert AA battery (not
included) negative end first.
• Replace Ignition Button Cap by tightening
clockwise.
• Press Red Ignition Button and hold in
to test battery. This will create spark
on burner that will start your grill.
(See
STARTING SECTION
for starting
operation).
Step 4: Install Battery
STEP 4
+
–
SET UP
MAINTENANCE &
TROUBLESHOOTING
1) After grill has cooled, use a soft cloth to clean exterior of grill.
2) Clean the cooking grates before and after cooking.
Note: Remove surface dust and grease.
3) Infrared Heat-Exchanger should be clean prior to each use.
a) Check for debris in the heat exchanger.
b) If debris is present, please remove it with a stiff brush.
4) Clean Side Shelves with mild detergent.
5) When grill is cooled, use grill cover to prolong life of grill.
6) When the Gas Insert is not in use:
a) Ensure that the Control Knob is off.
b) Ensure that the valve on gas tank is turned to Closed position.
c) Ensure that there is not gas leakage from the gas hose.
7) Leak Detection Method.
a) Inspect valve connections, port and regulator assembly.
b) Look for any damage or debris. Remove debris.
c) Inspect hose for damage.
d) Turn gas cylinder knob clockwise to Open position.
e) Pour soapy water or Leak Test Solution (sold separately) at the
connection spot of the gas cylinder to check whether there is
gas leakage.
NOTE: Check whether bubbles appear. (If there are no bubbles, there is no air leakage; If
bubbles appear, there is gas leakage.)
f) Repeat Leak Test at the connection spot at the gas entrance of the gas insert to check
whether there is gas leakage.
g) If you can not solve your problem by the above steps, please contact Vision Grills
Customer Service at [email protected] or www.visiongrills.com.
8) If you are having trouble getting to “HIGH”, review step “7” of “STARTING.” Again, make
sure to push in the Control Knob and turn all the way to the left, until the tick mark is
horizontal. If encountering further issues, contact Customer Service.
Watch For Bubbles
Manual Ignition (Match Ignition) Method of Operation
1. Put match in the ignition tool as
shown.
2. Light match, insert inside the
front right opening as shown.
3. Slide match to the inside back
of the Gas Insert, reaching the
burner.
(Rear Side View shown)
4. Turn the knob to Low and press it
down until it is lit.
If ignition does not occur within 5
seconds, turn the Control Knob to OFF
position. Wait 5 minutes and repeat
the lighting procedure.
5. Light the gas and observe flame
within the Heat Exchanger.
1
2
3
5
4
