Vision & Control Vicosys 5400 Скачать руководство пользователя страница 59

Страница: 59 / 64

vicosys

5400

Maintenance and Service

999.994.729.10-en-2.3

8 MAINTENANCE AND SERVICE

8.1 Maintenance

The device is maintenance-free. Depending on the operating environment, it

may have to be cleaned.

Cleaning the outside

•

The housing can be cleaned according to the conditions applicable to the

given protection class.

•

Clean the outside with a damp cloth.

•

Remove excessive dirt with an approved varnished steel sheet cleaner.

Refer to the instructions of the cleaner.

•

Cleaners must not be applied directly to the housing, and the housing must

not be bathed.

•

The interfaces must be clean and dry before the device is connected and

put into operation.

8.2 Service

Technical Support

Please contact our Technical Support if you have any technical questions

concerning our products. Competent employees will deal with your problems

and questions.
We will be glad to be of service:
Monday to Thursday 8:00 to 17:00, and Friday 8:00 to 15:00.
Vision & Control GmbH
Mittelbergstraße 16
98527 Suhl, Germany

Phone: +49 (0) 3681 7974-11

www.vision-control.com

Содержание Vicosys 5400

































































Результаты поиска

Содержание Vicosys 5400

Отзывы:

Похожие инструкции для Vicosys 5400

Бренды по названию

Популярные бренды

Vision & Control Vicosys 5400, Инструкция по эксплуатации

Результаты поиска

Содержание Vicosys 5400

Отзывы:

Похожие инструкции для Vicosys 5400

Бренды по названию

Популярные бренды