Vishay VT 200 Скачать руководство пользователя страница 4

Страница: 4 / 84

Table of Contents

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

4.4.2

Securing Load Receptor ..................................................................... 44

4.4.3

Checking Seal Status and Audit Trail Counter........................................ 44

GENERAL SYSTEM PARAMETERS..................................................... 45

5.1

PAR

ENU

......................................................................................... 45

5.1.1

Accessing the Menu and Editing Parameters.......................................... 45

5.1.2

PAR Menu Parameters ....................................................................... 46

5.1.3

Dual-scale Connecting And Parameter Settings ..................................... 47

5.2

SETUP

NSIDE

SETUP

ENU

) ............................................................. 47

5.2.1

Accessing the Menu and Editing Parameters.......................................... 47

5.2.2

SETUP 1 Parameters ......................................................................... 48

SERIAL COMMUNICATION .............................................................. 49

6.1

ERIAL

ORTS

ONFIGURATION

................................................................. 49

6.1.1

RS232 Serial Port ............................................................................. 49

6.1.2

RS485 Serial Port ............................................................................. 49

6.2

ETTING

ORT

UTPUT

ARAMETERS

.......................................................... 50

6.2.1

Setting Port 1 Output ........................................................................ 50

6.2.2

Setting Port 2 Output ........................................................................ 50

6.3

UTPUT

YPES

.................................................................................... 50

6.3.1

Local Printer..................................................................................... 50

6.3.2

Continuous Weight Output ................................................................. 50

Continuous Weight Data Block Composition LEO Format..................................................... 51

Continuous Weight Data Block Composition AND Format ................................................... 51

Two-Scale Operation...................................................................................................... 52

6.3.3

Continuous Weight With Tare ............................................................. 52

Data Block Composition.................................................................................................. 53

When Display Indication is Not Weight ............................................................................. 53

6.3.4

Print on Demand............................................................................... 53

6.3.5

Alibi Transmit................................................................................... 54

6.3.6

Alibi Mode Commands ....................................................................... 54

Transmit Displayed Weight ............................................................................................. 54

Command “ZERO” ......................................................................................................... 54

Print on Demand Character............................................................................................. 54

6.3.7

EDP Protocol Output.......................................................................... 55

Содержание VT 200





















































































Результаты поиска

Содержание VT 200

Отзывы:

Vishay VT 200, Техническое руководство, Страница: 4 / 84

Результаты поиска

Содержание VT 200

Отзывы: