These instructions do not apply to all vehicles. They are only meant as a general
guide due to the number of different makes & models.
For vehicle specific questions contact your vehicle’s manufacturer.
MONITOR INSTALLATION
When choosing a location to mount the monitor, make sure the monitor is in an area
that will not obstruct your vision while driving. It can be placed on the dashboard, or
on the windshield depending on the angle.
Choose a Location and Power Cable
1. Temporarily place the monitor stand
in the location that you have chosen.
2. If you are using the supplied Moni-
tor Wiring Harness, route the power
cable to the vehicle’s fuse box.
If you are using the 12V adaptor, route
the power cable to the vehicle’s ciga-
rette lighter socket/12V power outlet.
The cable must not interfere with the
safe operation of the vehicle.
Mounting the Monitor
Before permanently mounting the monitor, clean
the mounting area well with isopropyl alcohol,
then dry thoroughly.
1. With the two pieces of the oval hook & Loop
fastener attached to each other, peel the back-
ing paper from “Loop” side the oval shaped
Hook & Loop fastener. (Fig. 1)
2. Next align the Hook & Loop fastener with the
bottom of the monitor stand and press firmly to
adhere. (Fig. 2)
3. With the “Hook” half of the hook & loop fastener
attached to the “Loop” half you just attached to
the monitor, peel off the backing paper. (Fig. 3)
4. Then press the monitor stand firmly onto the
area you just cleaned. Adhesive reaches maxi-
mum strength in 24 hours. Moving the fastener
from its original position will weaken the adhe-
sive and may damage the mounting surface.
(Fig. 4)
To maximize the effectiveness of the Hook & Loop fastener, it is recommended that
the application be performed under the following conditions:
Surface temperature should be between 21 C and 38 C (70F and 100F).
Application below 10C (50F) should be avoided.
Application should not occur in direct sunlight.
Mounting should be protected from exposure to direct sunlight for a period of 24 hours.
Automotive video equipment installations can be difficult at times, even to the most
experienced of installation technicians. If you are not confident working with 12 volt
DC vehicle wiring, removing and reinstalling interior panels, carpeting, dashboards or
other components of your vehicle, please call our
Toll-Free Help Line 1-800-445-1797
and our in-house technical service team will answer your installation questions. If you
have vehicle specific questions, contact the vehicle’s manufacturer, or consider hav-
ing the VRBCS300WCOSC professionally installed.
VRBCS300WCOSC
Wireless Back-Up Camera
and Monitor
Before You Install
Parts
Installation & Operation
Installation & Operation
Dear Customer,
CONGRATULATIONS. The VRBCS300WCOSC Wireless Back-up Camera System,
when used as described, will give you years of dependable service in your car, truck,
RV, or mini-van. We have taken numerous measures in quality control to ensure that
your product arrives in top condition, and will perform to your satisfaction. In the
rare event that your VRBCS300WCOSC Wireless Back-up Camera System contains
a damaged or missing item, does not perform as specified, requires warranty ser-
vice, or you have an installation problem,
DO NOT RETURN THIS PRODUCT TO THE
STORE. PLEASE CALL OUR TOLL FREE NUMBER FROM THE U.S.A. AND CANADA
1-800-445-1797
and ask to speak with a member of our technical service team, or
submit your questions by e-mail to [email protected] and a member of our
technical service team will respond by e-mail to your questions. Our in-house techni-
cal service team will expedite delivery of your part, advise you on installation, or help
troubleshoot a problem with you. If your product needs warranty service, our techni-
cal service team representative will help you obtain the fastest remedy possible under
CAMERA INSTALLATION
You may mount the camera using the license plate’s top or bottom mounting
bolts or screws, make sure that it’s field of view is not obstructed. You may
mount the camera on the top or bottom of the license plate. Use the supplied
wedge shaped shims to adjust the angle that the camera is mounted.
1. Loosen the license plate bolts/screws,
then remove the rear license plate.
2. Insert each license plate bolt into a
supplied wedge, then through the bolt
holes of the camera, then through the
remaining wedges and the license
plate. (Fig.1)
3. Align with holes on vehicle and tem-
porarily tighten the license plate bolts/
screws. The wedges will angle the
camera down.
4. You will need to choose a route for the
camera’s power cable through the ve-
hicle’s body to the reverse light circuit.
Red LED Power Indictor
Image Orientation Button
Power ON/OFF Button
Brightness Control
Contrast Control
Red LED Power Indicator - When
the monitor is ON the red LED will
be lit. If there is power to the moni-
tor, but the monitor is OFF, the red
LED will be OFF.
Power Button - Press the Power
button to turn the display ON, the
red LED will be lit to indicate the
monitor is ON. Press it again to turn
the display OFF, the red LED will
turn off.
MONITOR CONTROLS
Contrast Control - There are 13 levels of contrast. To adjust the contrast, press the
Contrast Control button. Press the button to increase the contrast, at the highset level
it will return to the lowest level.
Brightness - There are 13 levels of brightness. To adjust the brightness, press the
Brightness Control button. Press the button to increase the brightness, at the highset
level it will return to the lowest level.
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Power Cable with 12 Volt Cigarette Lighter Adaptor
1. Insert the small 12 Volt DC plug of the power cable into
the left side of the monitor.
2. Plug the 12 Volt cigarette lighter adaptor into the vehi-
cle’s cigarette lighter socket.
3. Press the ON/OFF button to turn the monitor ON.
Fig.1
This device, as well as all other wireless devices, may be subject to interfer-
ence. Interference may be caused by cell phones, Bluetooth headsets, Wi-FI
routers, power lines and other various electrical equipment, etc.
Hard Wired to the Fuse Box
1. Disconnect the negative battery cable from the vehicle’s negative battery terminal.
2. Connect the Red wire to the 12 Volt +/ACC terminal in the vehicle’s fuse box. See
vehicle’s owner’s manual for fuse box diagram.
3. The ground cable must be located on an area of metal on the vehicle’s body/fire-
wall that does not have any vehicle components behind it. Sand off any paint to
reveal bare metal, this area will be your chassis ground.
4. Drill a hole for the supplied self tapping sheet metal screw. Make sure there are no
vehicle components behind where you are drilling the hole.
5. Strip the insulation from the end of the black wire 1.3cm and wrap the wire around
the self-tapping sheet metal screw before tightening.
6. Re-connect the negative battery cable.
7. Plug the power cord into the monitor, use the ON/OFF button to turn the monitor ON & OFF.
MONITOR POWER CONNECTION
There are two ways to supply the monitor with power, one uses a 12 Volt ciga-
rette lighter adaptor plugged into the vehicle’s cigarette lighter socket, and the
other uses a wiring harness hard wired to the vehicle’s fuse box.
NOTE: UNDER EXTREME BRIGHT LIGHT CONDITIONS, THE SCREEN IMAGE
MAY TAKE A FEW SECONDS TO STABLIZE. PLEASE WAIT UNTIL THE IMAGE
HAS STABLIZED BEFORE BACKING UP.
