Vinten FHR-35 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 32

Vinten FHR-35 Скачать руководство пользователя страница 4

2

Follow all warnings and instructions marked on the product
and in this manual. Safety warnings are included in this
manual. These safety instructions must be followed to avoid
possible personal injury and damage to the product.

WARNING!

Do not install this product onto a bracket,

support or other equipment that is not designed to support
the weight of the product and its payload. All supports must
comply with local government regulations.

WARNING!

The fitting of non-approved parts and

accessories, or the carrying out of non-approved alterations
or servicing can be dangerous and could affect the safety of
the product. It may also invalidate the terms and conditions
of the product warranty.

WARNING!

This product must be connected to a power

supply of the same voltage (V) and current (A) as
indicated on the product and described in the specification
section of this manual. To reduce the risk of electric
shock, do not remove the covers. No user-servicable parts
inside. Refer all servicing to qualified service personnel.

WARNING!

This product is Class 1 equipment. For safe

operation this equipment must be connected to a power
supply that has a protective earth connection (US:
ground).

CAUTION!

This product is designed for robotic use only

and is operated remotely. Do not attempt to manually
operate this product.

CAUTION!

Slots and openings are intended for ventilation

purposes to ensure reliable operation of the product and
protect it from overheating. Do not block or cover any slots
and openings.

CAUTION!

Do not use solvent or oil-based cleaners,

abrasives or wire brushes to remove accumulations of dirt
as these damage the protective surfaces. To clean
mechanical surfaces, use only detergent-based cleaners.

WARNING!

Risk of personal injury. All personnel must be

fully trained and adhere to correct manual handling
techniques. It is the responsibility of the individual and the
local organisation to enforce safe working practices at all
times.

WARNING!

Risk of personal injury or injury to others. All

personnel must be fully trained and adhere to local health
and safety laws and guidelines. It is the responsibility of the
local organisation to enforce safe working practices at all
times.

For your personal safety, read these instructions. Do not
operate the product if you do not understand how to use it
safely. Save these instructions for future reference.

Electrical Connection

Basic Electrical Insulation (Class 1 equipment)

Ventilation and Overheating

Cleaning and Maintenance

WARNING!

The IEC connector is the primary disconnect

device and must be accessible both during and after
installation of the product.

WARNING!

Inspect the AC cable regularly for signs of

wear or damage. If the AC cable is damaged, the product
must be returned to Vinten Radamec for repair.

FHR-35 Robotic Pan and T

ilt Head

Safety and Warnings

«
...
2
3
4
5
6
...
»

Содержание FHR-35

































Отзывы:

Нет отзывов