Viking MICROFAST VK3271 Скачать руководство пользователя страница 3

MICROFAST

®

 QUICK 

RESPONSE UPRIGHT 

SPRINKLER VK3271 (K4.2)

TECHNICAL DATA

Page 3 of 3

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: [email protected]

Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com.

Form No. F_061614     18.11.05     Rev 17.2.P65

Approval Chart 1 (UL)

Microfast

®

 Quick Response

 

Upright Sprinkler VK3271

 

Maximum 175 PSI (12 bar) WWP

Base Part 

Number

1

SIN

Thread Size

Nominal K-Factor

Overall Length

Listings and Approvals

3

NPT

BSP

U.S.

metric

2

Inches

mm

cULus

VdS

LPCB

      

06931B

VK3271

--

10 mm

4.2

57

2-3/16

56

--

A1

--

A1

7

Approved Temperature Ratings

A - 135 °F (57 °C), 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C), and 

286 °F (141°C)

Approved Finishes

1 - Brass, Chrome, White Polyester

5,6

, and Black Polyester

5,6

Footnotes

Base part number is shown. For complete part number, refer to Viking’s current price schedule.

Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0.

This table shows the listings and approvals available at the time of printing. Check with the manufacturer for any additional approvals.

4

 Listed by Underwriters Laboratories Inc. for us in the U.S. and Canada

5

 Other colors are available on request with the same Listings and Approvals as the standard colors.

6

 cULus Listed as corrosion resistant.

7

 CE Certified, Standard EN 12259-1, EC-certificate of conformity 0786-CPD-40131

IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 

for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest 

edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organiza-

tions, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable.

Replaces Form No. F_061614 Rev 17.2

(Added P65 Warning.)

Содержание MICROFAST VK3271









Отзывы: