2
Specifications and Installation
K-1900D-2 Hot Line Desk Phone
K-1900W-2 Hot Line Wall Phone
K-1900-6 Hot Line Desk Phone
Viking
offers two variations of hot-line phones and one network dialer. Below are model numbers and descriptions of the Hot Line phones
Viking offers. Each model is designed for specific applications, including varying mounting capabilities and levels of vandal protection.
The following sections describe the product model numbers, their applications, installation and specifications.
Important:
Use a minimum wire gauge of 26 when connecting the
K-1900
phone to the public switched network.
To install the
K-1900D-2
insert the RJ11 plug
into a standard RJ11 jack as shown to the right.
Dimensions:
230mm x 210mm x 120mm (9.0”
x 8.25” x 4.75”)
Shipping Weight:
1.36 Kg (3 lbs)
Connections:
RJ11
Colors:
Red or Ash
RJ11
(not included)
C.O. Line or Analog
PABX/KSU Extension
To install the
K-1900W-2
line up the pins
of the RJ11W jack with the slots on the
back of the phone, insert and press down
as shown to the right.
Dimensions:
102mm x 121mm x 229mm
(4.0” x 4.75” x 9.0”)
Shipping Weight:
1.36 Kg (3 lbs)
Connections:
RJ11W
Colors:
Red or Ash
RJ11W (not included)
C.O. Line or Analog
PABX/KSU Extension
The
K-1900-6
Hot-Line Dialer Network
can be used with any carbon microphone
handset and a SPDT (Single Pole
Double Throw) hook switch or typical
500, 554, 2500 and 2554 phones. Attach
wires as shown to the right. An electronic
ringer may be used if inbound call
capability is required.
Required Handset Type:
Carbon or
Carbon Compatible Electric microphone
Required Hookswitch:
Single pole
double throw
Dimensions:
88.9mm x 68.6mm x
33mm (3.5” x 2.7” x 1.3”)
Shipping Weight:
0.45 Kg (1.0 lb)
Connections:
Miniature spade
receptacles
Compatible Phones:
500, 554, 2500
and 2554
White
Black
Red
White or
Green
N.O.
N.C.
0.47 mF @ 250V
Capacitor
(included)
Optional Ringer
(not included)
0.56"
(2) 0.136" Diameter
Mounting Holes
3.05"
Carbon Mic
Handset
(not included)
T
R
S1
S2
RX2
RX1
TX1
TX2
Green
Red
Slate/Brown
Slate/Yellow
Slate
C.O. Line
or Analog
PABX/KSU
Extension
SPDT
Hookswitch
(shown on hook
)
K-1900-6 PCB with Standard Network
Mounting Bracket (included)
Note:
If the phone has a
ringer, the included capacitor
MUST be installed as shown.
-or-
Programing
While in the programming mode, two beeps indicate a valid programming entry. An invalid entry will be indicated with
three beeps. To exit programming, simply hang-up the
K-1900
Series phone.
A. Access ing the Programming Mode
1. Using the Security Code
Step 1.
Connect the
K-1900
Series device to an analog C.O. line, or an analog PABX/KSU station.
Step 2.
From a touch tone phone, call into the
K-1900
Series Phone.
Step 3.
Listen for at least one ringback in the calling phone and then take the
K-1900
phone off-hook (answer the phone).
Step 4.
From the Touch Tone phone, enter your six digit security code (factory set to
845464
- see section
E
).
Step 5.
A double beep indicates the
K-1900
Series phone is in the programming mode (see sections
B-G
). If six digits
are entered and no beeps are heard, an incorrect security code has been entered. Repeat steps
2-5
or follow
directions in
2. Without a Security Code
below.
T
E
L
E
P
H
O
N
E
Optional VE-9x12 Weatherproof
Housing, see DOD# 413
