K. Programming Examples
These examples would be entered after following the steps in section A.
...to dial a 9, pause 4 sec, and dial 1 (612) 555-1212 when a 2 is entered
...to dial the number 9#888
✱
8 when a 1 is entered
...to store a 9, pause 1 second, 911 in emergency position one
...to clear the number stored in memory position 15
Programming the K-1900-1...
Enter Digits
Enter Location
Note:
✱
7 and
✱
8 place a four or one second pause respectively.
9
✱
716125551212
9
✱
#888
✱✱
8
9
✱
8911
#02
#01
##5
#15
H. Restrict User Dialing
(dedicated dialer mode only)
The K-1900-1 can be programmed to restrict any user dialing by disconnecting on any Touch Tone or pulse dialing
detected after the unit has dialed. This feature can only be enabled in the “dedicated dialer mode”. To allow user
dialing, enter
✱
4 while programming. To prohibit user dialing (factory default) enter
✱
3 while programming.
C. Security Code
A six digit number can be used to access the programming mode. The security code has been factory set to
845464 (V-I-K-I-N-G). It is recommended that you change the security code to a personal 6 digit number.
Note: The security code must be six digits in length and can NOT contain a
✱
or #.
D. Selecting the Dialer Mode
The K-1900-1 can be programmed as a speed dialer or a dedicated multi-number dialer (see Operation sections A.
and B.) To configure the K-1900-1 as a dedicated dialer (factory default), enter ##0 while programming. To
configure the K-1900-1 as a speed dialer, enter ##1 while programming.
E. Hang-up Before Dialing
If your telephone’s Touch Tones break dial tone while entering the desired memory position, the K-1900-1 can be
programmed to hang up momentarily (approximately 1 second) before dialing. To disable the hang-up before
dialing enter ##2 while programming. To enable the hang up before dialing (factory default), enter ##4.
F. Emergency Numbers
The K-1900-1 can be programmed to dial specific telephone numbers when 911 or 311 are entered. If no telephone
numbers are programmed in these memory positions (##5 and ##6) they will default to the factory setting and the K-
1900-1 will dial 911 or 311 respectively.
G. Pulse/Tone Dialing
The K-1900-1 can be programmed to dial fast or slow in both Touch Tones or pulse. To program the K-1900-1 to
pulse dial, enter
✱
0 while programming. To program the K-1900-1 to Touch Tone dial (factory default), enter
✱
9
while programming. For normal dialing speed (factory default), enter
✱
1 while programming. For fast dialing speed,
enter
✱
2 while programming. Normal dialing speed is 120ms on/off for Touch Tones and 10 pps for pulse. Fast
dialing speed is 50ms on/off and 20 pps for pulse.
Note:
✱
’s and #’s can not be pulse dialed.
I. Automatic Pause Before Dialing
A short pause is inserted before the K-1900-1 will dial. This insures that dial tone has been returned. To program a
short pause (approximately 500 ms), enter
✱
6 while programming. For a long pause (approximately 1 second,
factory default), enter
✱
5.
Note: This feature is only operational with the hang-up before speed dialing feature enabled, enter ##4 while
programming.
J. Pauses in the Dialing String
The K-1900-1 allows pauses to be programmed in the dialing string for such applications as dialing pagers, etc. To
program a four second pause, enter a
✱
7 at any point in the dialing string, while in programming. For a one second
pause, enter
✱
8.
