F. Door Strike Time
The actual time the door strike relay is energized is controlled by location
#40
. The time can be set from 00 to 99 seconds, (an entry
of “00” gives 0.5 seconds). In order to use this feature, be sure the relay door strike code is set (see section
G
).
6
E. Speed Dial Numbers
The
K-1205
Entry Controller can be programmed with up to twelve 46 digit numbers. Each number can also be programmed with
special features such as pauses, and the Touch Tones “
Q
” and “
#
”. Each of the special characters count as a single digit. Each of
the speed dial positions
#01
to
#12
pertain to the corresponding button on the front of the
K-1205
. The button “
0
” uses position
#10
,
the “
Q
” uses position
#11
and the “#” uses position
#12
. To program a speed dial position, enter programming (see section
A
) then
enter the desired number followed by the selected position. To clear a position, only enter a “
#
“ followed by the position number with
out any preceding number. The
K-1205
also has the capability to dial a second phone number if there is no answer or busy at the
first number. This can be used if the tenant wants the visitor to call their cell phone if they are not at home. To program a second
number, be sure that position
#43
is programmed with the desired maximum ring time, then enter the first number to be dialed, fol-
lowed by “
#24
”. A single beep should be heard. Next enter the second number to be dialed followed by “#“ plus the memory loca-
tion. The total number of digits cannot exceed 46 for each position (45 digits if two numbers are programmed).The following are
examples of speed dial number entries:
B. Security Code (memory location #47)
This six digit number can be used to access the programming mode. The security code has been factory set to
845464
(V-I-K-I-N-
G). It is recommended that you change the security code to a personal 6 digit number. To change the security code, access pro-
gramming (see
Programming
section
A
). Enter six digits 0-9 followed by
#47
. If you have forgotten your security code, follow the
steps in
Programming
section
A, 2. Accessing the Programming Mode Without the Security Code)
.
Note:
The security code
must be six digits in length and can NOT contain a
Q
or #.
C. Keyless Entry Codes
The
K-1205
can be programmed with up to 50 keyless entry codes. This feature allows a visitor to let themselves in by entering a
preprogrammed code on the
K-1205
keypad. Each keyless code can contain from 1 to 6 digits and is programmed by entering the
digits into any of the locations
#50
to
#99
. To clear a location enter “
#
” followed by the position number without any preceding num-
ber. The “
Q
” and “
#
” keys can also be used in the keyless codes by substituting “
#20
” and “
#21
” (respectively) when programming
a keyless position.
D. Quick Programming Features
The
K-1205
is programmed through the incoming phone line. The programming commands are structured so that they do not
interfere with the commands of a
C-1000B
controller.
#01
-
#12
#40
#41
#42
#43
#44
#45
#47
#50 - #99
- then - Enter Memory Location
Speed dial numbers ..................................................................................................
Door strike time in sec (factory 05, 00 =.5 sec)**........................................................
Door strike code (factory 6, no digits disables) ..........................................................
Maximum call time in min (factory 3, 0 = .5 min, no digits disables)** .......................
Maximum ring time in sec (factory 20, 00 disables)** ...............................................
Silence Time Out in sec (factory 10, 00 disables)** ..................................................
Talk/listen delay time in .1 sec (factory 2)** ...............................................................
Security code (factory 845464)** ...............................................................................
Keyless entry codes ..................................................................................................
Dial a (
Q
) ..................................................................................................................
Dial a (#) ...................................................................................................................
Add a 4 second pause ..............................................................................................
Add a 1 second pause .............................................................................................
Second phone number selector ................................................................................
Normal dialing speed* ..............................................................................................
Fast dialing speed .....................................................................................................
Hang up on dial tone enable* ...................................................................................
Hang up on dial tone disable ....................................................................................
Reset all programming to factory default settings ...................................................
Hang up from programming ......................................................................................
0-46 digits***
2 digits
1-2 digits
1 digit
2 digits
2 digits
1 digit
6 digits
1-6 digits
#20
#21
#22
#23
#24
#30
#31
#32
#33
###
##7
Enter Digits
then
then
then
then
then
then
then
then
then
Step 2 - Enter Digits
5551234#01
9#233334444#07
23#20#21#08
22#24
(beep)
33#12
Step 1 (see section A)
Enter programming
Enter programming
Enter programming
Enter programming
To Program the K-1205 to...
...store 555-1234 at the first button position
...store a 9, a 1 second pause, then 333-4444 in the seventh button position
...store a 23
Q
# in the eight position
...store a first number of 22 and a second number of 33 in the “#“
button position
*Factory settings
** Cannot contain “
Q
“ or “#“
(see #20 and #21)
***
45 digits maximum if two numbers are pro-
grammed in one memory location
Notes:
1. A single or double beep indicates a
valid entry, three beeps indicate an error. 2.
“
Q
“ or “#“, pauses or second phone number
selector occupy one digit of memory
.
