background image

Service & Registration

19

• New units are cleaned at the factory

to remove any visible signs of dirt, oil,
grease, etc. remaining from the
manufacturing process. Some stainless
steel parts may have a plastic protective
wrapper which must be peeled off. The
cooktop should be washed thoroughly
with hot, soapy water and then rinsed and
wiped dry to remove these film residues
and any installation dust or debris before
being used for food preparation.

18

A qualified installer should carry out the
following checks:

h

Check top burner
ignition. The low
flame should light at
every port.

h

Starting with the left
front burner, turn the
corresponding knob to the HI position –
see drawing for proper flame height.

h

Repeat steps for other burners.

3.8 cm

0.95 cm

Performance Checklist

Final Preparation

1

1

1

1

2

2

1

Replace the burner caps and grates.

Note:

The narrow edge of grate goes toward center of unit.

• All stainless steel body parts should be

wiped regularly with hot, soapy water
and with a liquid cleanser designed for
this material if build-up occurs.

DO NOT

USE

steel wool, abrasive cloths, cleansers,

or powders. If it is necessary to scrape
stainless steel to remove encrusted
material, soak with hot, wet cloths to
loosen the material, then use a wood
or nylon scraper.

DO NOT USE

a metal

knife, spatula, or any other metal tool
to scrape stainless steel. Scratches are
almost impossible to remove.

Final Installation

If service is required, call your dealer or authorized service agency. The name of the authorized
service agency can be obtained from the dealer or distributor in your area.

Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are unable to obtain the name of an
authorized service agency, or if you continue to have service problems, contact the Viking
distributor for your area or visit vikingrange.com.

The model and serial number for your cooktop can be found by looking under the unit.

If service requires installation of parts, use only authorized parts to insure protection under the
warranty.

Keep this manual for future reference.

Replacement Parts

Only authorized replacement parts may be
used in performing service on the cooktop.
Do not repair or replace any part of the
appliance unless specifically recommended
in the manual. All other servicing should be
referred to a qualified tecnician.

Содержание CNVGSU104











Отзывы: