manualshive.com logo in svg
background image

IMPORTANT

5

Please Read and Follow

4

IMPORTANT–

Please Read and Follow!

W A R N I N G

ELECTRICAL SHOCK HAZARD

• Electrically ground dishwasher.
• Connect ground wire to green ground

connector in terminal box.

• 

DO NOT

use an extension cord.

• Failure to follow these instructions, can

result in death, fire or electrical shock.

W A R N I N G

TIP OVER HAZARD

• DO NOT

use dishwasher until

completely installed.

• DO NOT

push down on open door.

• Doing so can result in serious injury 

or cuts.

W A R N I N G

EXCESSIVE WEIGHT HAZARD

Use two or more people to move and
install dishwasher. Failure to do so can
result in back or other injury.

W A R N I N G

Disconnect the electrical power supply and
place a tag at the disconnect switch
indicating that you are working on the
circuit.

W A R N I N G

Be sure electrical power is turned off at
circuit breaker or fuse box before servicing
or installing unit. Do not use an extension
cord for this appliance.

W A R N I N G

Improper connection of the equipment –
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or serviceman if you are in
doubt as to whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance; if it will not fit
the outlet, have a proper outlet installed by
a qualified electrician.

W A R N I N G

Plumbing connections must comply with
applicable sanitary, safety, and plumbing
codes. 

C A U T I O N

The dishwasher has a factory installed
backflow preventer. Do Not add an additional
check valve.

A GFI 

shall be used if required by NFPA-70

(National Electric Code), federal/state/local
laws, or local ordinances.

• The required use of a GFI is normally

related to the location of a receptacle with

respect to any significant sources of water

or moisture.

• Viking Range Corporation will NOT

warranty any problems resulting from GFI

outlets which are not installed properly or

do not meet the requirements below.

If the use of a GFI is required

, it should be:

• Of the receptacle type (breaker type or

portable type NOT recommended)

• Used with permanent wiring only

(temporary or portable wiring NOT

recommended)

• On a dedicated circuit (no other

receptacles, switches or loads in the

circuit)

• Connected to a standard breaker of

appropriate size (GFI breaker of the same

size NOT recommended)

• Rated for Class A (5 mA +/- 1 mA trip

current) as per UL 943 standard

• In good condition and free from any

loose-fitting gaskets (if applicable in

outdoor situations)

• Protected from moisture (water, steam,

high humidity) as much as reasonably

possible

Содержание 301 Series













Отзывы: