manualshive.com logo in svg

Viking Access Systems T 21, Инструкции по установке и информация о безопасности

Поделиться
Скачать
Viking Access Systems T 21 Скачать руководство пользователя страница 19

VIKING TECHNICAL SUPPORT 1.800.908.0884

1 7

GATE OPERATOR INSTALLATION

STEP 1

Install the Clutch and cut the 
Arm Assembly to achieve 
the desired dimensions for 
“D” and “E” according to the 
formulas provided on page 16.

STEP 2

With the gate at the closed, 
install the Arm Assembly. 
Check that the dimensions 
correspond accordingly to the 
formulas provided on page 16.

!

 

IMPORTANT:

 

When attaching the Arm Assembly to the gate, if the “Gate Bracket” is not 

welded to a frame member that runs the full length of the gate, the operator may damage 
the gate. Do not attach the Gate Bracket to only a few pickets.

!

 

TIP: 

Leave some additional material 

when cutting the Arm Assembly to 
allow for adjustment.

!

 

TIP: 

Use C-clamps or tack-weld the Arm 

assembly in place until Step 3 has been 
completed.

STEP 3

With the Clutch installed and released, 
manually move the gate to both limits. 
Verify the following:
1.  The gate reaches the desired limits.
2.  The Arm does not bind at any point.

STEP 4

Once satisfied with the installation and 
movement of the gate, weld the arm 
pieces securely. Paint the Arm to protect 
against rusting.

STEP 5

Rotate the Clutch until it lines up with the 
notches on top of the Output Shaft and 
insert the Clutch Key.

STEP 6

Verify the Clutch is adjusted properly.
•  Both sides adjusted 

evenly

.

•  Handle is locked, 

by hand

, and 

positioned horizontally at 0°.

With the Clutch Key removed, the 
Clutch should not slip with moderate 
force applied to the gate. 

Содержание T 21



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды