Viking Access Systems Q-7 Скачать руководство пользователя страница 39

Страница: 39 / 50

VIKING TECHNICAL SUPPORT 1.800.908.0884

3 7

LED References

Use the table below to identify the corresponding “TS Ref#” and refer to page 38-41 for
further troubleshooting.

TROUBLESHOOTING

# LED

Status

Meaning

Pg 41

TS Ref#(s)

“C Loop”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the
C Loop terminal (pg 32, 42).

9, 10

10 “Open”

OFF

Normal Condition.

SOLID

Control board is receiving an input from a device connected to any of
the following input terminals: Exit, Fire, Strike or Open (pg 31, 42).

9, 10

“STOP”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the
Stop terminal (pg 31, 42).

9, 10

FLASHING

There is a problem with the required monitored sensor(s) connected
to the “UL” input terminal (pg 10-11)

16, 22

12 “Close”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the
Close terminal (pg 31, 42).

9, 10

13 “Siren”

OFF

Normal Condition.

SOLID

Second consecutive obstruction has been detected. (pg 26).

11, 13, 1, 2

FLASHING

Batteries are critically low.

1, 2

14 “Aux. Pwr”

OFF

No voltage output on these terminals at the moment.

SOLID

There is 24VDC output on these terminals at the moment.

15 “Diagnose”

OFF

Normal Condition.

FLASHING

Errors have been detected; Check LCD Display for ERR messages (pg 40).

16 “Close Limit”

OFF

Gate is not at the close limit position.

SOLID

Gate is at the close limit position.

FLASHING

Close limit position has been erased or not set (pg 20-21).

17 “Open Limit”

OFF

Gate is not at the open limit position.

SOLID

Gate is at the open limit position.

FLASHING

Open limit position has been erased or not set (pg 20-21).

18 “ODS”

OFF

Normal Condition.

SOLID

Obstruction has been detected. (pg 26).

11, 13, 1, 2

FLASHING

Overload has been detected. (pg 26).

11, 13, 1, 2

19 “Timer”

OFF

The close timer is turned OFF or gate is not at the open limit if the timer is
turned ON. (pg 24).

SOLID

Gate is at Open Limit, Timer is turned ON and counting down to close. (pg
24).

FLASHING

Gate is at Open Limit, Timer is turned ON but is not timing out due to a
conflicting command. (pg 24).

9, 10

“AC VOLTAGE OUTPUT”

SOLID

Normal Condition.

OFF

There is no output voltage from the Modular Power Box.

“PROTECTION WORKING”

SOLID

Normal Condition.

OFF

EMI Board is damaged and circuit is not protected . Replace EMI Board.

“AC VOLTAGE INPUT”

SOLID

Normal Condition.

OFF

Incoming power to Modular Power Box is not sufficient.(pg 18).

23 “AC POWER”

SOLID

Normal Condition for High Voltage installations.

OFF

High Voltage is not supplied to the Power Box Assembly (pg 18).

Содержание Q-7



















































Результаты поиска

Содержание Q-7

Отзывы:

Похожие инструкции для Q-7

Бренды по названию

Популярные бренды

Viking Access Systems Q-7, Руководство по установке

Результаты поиска

Содержание Q-7

Отзывы:

Похожие инструкции для Q-7

Бренды по названию

Популярные бренды