manualshive.com logo in svg

Viglen vig830s, Руководство пользователя

Поделиться
Скачать
Viglen vig830s Скачать руководство пользователя страница 11

V1.0                                   Vig830S Motherboard Manual 

10 

  Supports PCI Express GEN1 frequency of 1.25 GHz resulting in 2.5 Gb/s each 

direction (250 MB/s) per lane. Maximum theoretical bandwidth on interface is 4GB/s 
in each direction, simultaneously, when operating in x16 mode. 

 
Audio Subsystem 

 
The motherboard supports Intel High Definition Audio through a Realtek ACL887 audio 
codec.  
 
These audio connectors are used for audio devices. It is easy to differentiate between 
audio effects according to the colour of audio jacks. 
 

 

Figure 4:

 Audio Connectors 

 

  Line-In (Blue) - Line In, is used for external CD player, tape-player or other audio devices. 

  Line-Out (Green) - Line Out, is a connector for speakers or headphones. 

  Mic (Pink) - Mic, is a connector for microphones. 

 

Notes:

 

If you want to configure a 8-channel audio output: Use a chassis with HD audio 

module in the front panel to support an 8-channel audio output. 
 
 

Table 1

: Audio channel configuration 

Audio 2.1, 4.1, 5.1, or 7.1-channel configuration 

 

 

 

LAN Subsystem 

The LAN subsystem consists of the following: 
 
• Intel I219LM Gigabit Ethernet Controller (10/100/1000 Mb/s)  
• Intel Q87 Express Chipset  
• RJ-45 LAN connector with integrated status LEDs  
 
Additional features of the LAN subsystem include:  
• CSMA/CD protocol engine  
• LAN connect interface between the PCH and the LAN controller  
• Conventional PCI bus power management  

•  ACPI technology support  
•  LAN wake capabilities  

• ACPI technology support  

Содержание vig830s














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды