Viglen Vig560s Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 86

background image

Vig560s Motherboard Manual

9

Serial ATA Technology

The motherboard supports the Serial ATA technology through the Serial ATA
interfaces and the Intel® ICH6. The SATA specification allows for thinner, more
flexible cables with lower pin count, reduced voltage requirement, and up to 150
MB/s data transfer rate.

8-Channel High Definition Audio

Onboard is the Realtek® ALC861 7.1-channel audio CODEC. This CODEC is fully-
compliant with Intel® High Definition Audio standard (192 KHz, 24-bit audio). With
the CODEC, 8-channel audio ports, and S/PDIF interfaces, you can connect your
computer to home theatre decoders to produce crystal-clear digital audio.

S/PDIF Digital Sound Ready

The motherboard supports the S/PDIF Out function through the S/PDIF interface at
mid board. The S/PDIF technology turns your computer into a high-end
entertainment system with digital connectivity to powerful audio and speaker
systems.

USB 2.0 Technology

The motherboard implements the Universal Serial Bus (USB) 2.0 specification,
dramatically increasing the connection speed from the 12 Mbps bandwidth on USB
1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.

Additional BIOS Features:

Crash Free BIOS 2

This feature allows you to restore the original BIOS data from the support CD in case
when the BIOS codes and data are corrupted. This protection eliminates the need to
buy a replacement ROM chip.

Q-Fan Technology

The ASUS Q-Fan technology smartly adjusts the fan speeds according to the system
loading to ensure quiet, cool, and efficient operation.

EZ Flash BIOS

With the ASUS EZ Flash, you can easily update the system BIOS even before
loading the operating system. No need to use a DOS-based utility or boot from a
floppy disk.

«
...
8
9
10
11
12
...
»

Содержание Vig560s























































































Отзывы:

Нет отзывов

Похожие инструкции для Vig560s

Бренд: Alcad Страницы: 98

B360 GAMING PLUS

Бренд: MSI Страницы: 112

Бренд: Supero Страницы: 86

Бренд: ZiLOG Страницы: 41

Бренд: ASROCK Страницы: 30

Бренд: Advantech Страницы: 118

Spacewalker AK32

Бренд: Shuttle Страницы: 89

WizFi360-EVB-Pico

Бренд: Wiznet Страницы: 29

Бренд: Texas Instruments Страницы: 21

Бренд: Texas Instruments Страницы: 19

Бренд: Acorp Страницы: 66

Бренд: JETWAY Страницы: 48

ISL70321SEHDEMO1Z

Бренд: Intersil Страницы: 9

Бренд: Aaeon Страницы: 56

Бренд: SOYO Страницы: 94

Бренд: National Semiconductor Страницы: 22

Бренд: IEI Technology Страницы: 145

Бренд: Seanix Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды