Viglen L440GX+ Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 42

background image

1

Chapter: 1 Overview

Introduction

This manual describes the Viglen motherboard inside your computer. The
motherboard is the most important part of your computer. It contains all of the CPU,
memory and graphics circuitry that makes the computer work.

The motherboard contains the very latest CPU design, Pentium III processors, which
include Intel’s

MMX technology

. MMX technology adds a total of 57 new

instructions to the CPU, all of which are designed to vastly improve both multimedia
and communications on your PC. The combination of the Intel Pentium III
processors, MMX technology and Viglen expertise make this a formidable computer.

This manual contains technical information about the Viglen motherboard
and other hardware components inside your computer. If you are new to computers
we recommend that you read the user guide first. If you are an experienced
computer user this manual should provide all the information you will need to
perform simple upgrades and maintenance.

We hope that this manual is both readable and informative. If you have any
comments or suggestions about how we could improve the format then please fill out
the form at the back of the manual and send it to us.

Above all we hope that you enjoy using your Viglen computer.

1
2
3
...
»

Содержание L440GX+











































Отзывы:

Нет отзывов

Похожие инструкции для L440GX+

Бренд: Garmin Страницы: 8

Бренд: NXP Semiconductors Страницы: 14

Бренд: Xeltek Страницы: 19

Бренд: Biostar Страницы: 49

Бренд: Advantech Страницы: 3

Бренд: JETWAY Страницы: 41

Бренд: Zetex Страницы: 8

Бренд: IEI Technology Страницы: 131

microComponents mp6-XEVA

Бренд: Bartels Mikrotechnik Страницы: 9

Бренд: TYAN Страницы: 63

Бренд: NXP Semiconductors Страницы: 32

Бренд: AOpen Страницы: 8

Бренд: TYAN Страницы: 47

Бренд: Biostar Страницы: 63

Бренд: Renesas Страницы: 30

Бренд: AOpen Страницы: 44

Бренд: IBASE Technology Страницы: 81

Бренд: Advantech Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды