background image

V1.0                                                         Page 10 of 17 

System Memory 

The boards have four DIMM sockets and support the following memory features: 

• 1.8 V and 1.9V DDR2 SDRAM DIMMs with gold-plated contacts. 
• Unbuffered, single-sided or double-sided DIMMs with the following restriction: 
  Double-sided DIMMS with x16 organization are not supported. 
• 8 GB maximum total system memory total amount of addressable memory. 
• Minimum total system memory: 128 MB 
• ECC and Non-ECC DIMMs 
• Serial Presence Detect 
• DDR2 667 MHz or DDR2 533 MHz SDRAM DIMMs 

NOTES 

• Remove the PCI Express x16 video card before installing or upgrading memory to avoid 
  interference with the memory retention mechanism. 
• To be fully compliant with all applicable DDR SDRAM memory specifications, the board 
  should be populated with DIMMs that support the Serial Presence Detect (SPD) data 
  structure. This allows the BIOS to read the SPD data and program the chipset to    
  accurately configure memory settings for optimum performance. If non-SPD memory is  
  installed, the BIOS will attempt to correctly configure the memory settings, but  
  performance and reliability may be impacted or the DIMMs may not function under the  
  determined frequency. 
  
The following table lists the supported DIMM configurations. 

    

Table 6. 

DIMM 
Capacity 

Configuration 

SDRAM 
Density 

SDRAM Organization 
Front-side/Back-side 

Number of SDRAM 
Devices 

128 MB 

SS 

256 Mbit 

16 M x 16/empty 

256 MB 

SS 

256 Mbit 

32 M x 8/empty 

256 MB 

SS 

512 Mbit 

32 M x 16/empty 

512 MB 

DS 

256 Mbit 

32 M x 8/32 M x 8 

16 

512 MB 

SS 

512 Mbit 

64 M x 8/empty 

512 MB 

SS 

1 Gbit 

64 M x 16/empty 

1024 MB  DS 

512 Mbit 

64 M x 8/64 M x 8 

16 

1024 MB  SS 

1 Gbit 

128 M x 8/empty 

2048 MB  DS 

1 Gbit 

128 M x 8/128 M x 8 

16 

 

Note:

 In the second column, "DS" refers to double-sided memory modules (containing two rows of DDR 

SDRAM) and "SS" refers to single-sided memory modules (containing one row of DDR SDRAM).

 

 

 
 
 
 
 
 
 
 
 

Содержание Intel D955XBK


















Отзывы: