Quick Start Guide
VB-CAM-001
HD Webcam
VB-CAM-001_QSG Rev.1a 01-18-19
Copyright © 2019 ViewSonic Corporation. All rights reserved.
Compliance Information
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference that may cause undesired operation.
Warning:
by the party responsible for compliance could void your authority to operate the
equipment.
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade and the third
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
%
1
.
0
<
%
1
.
0
)
b
P
(
d
a
e
L
%
1
.
0
<
%
1
.
0
)
g
H
(
y
r
u
c
r
e
M
%
1
0
.
0
<
%
1
0
.
0
)
d
C
(
m
u
i
m
d
a
C
Hexavalent Chromium (Cr
6+
%
1
.
0
<
%
1
.
0
)
%
1
.
0
<
%
1
.
0
)
B
B
P
(
s
l
y
n
e
h
p
i
b
d
e
t
a
n
i
m
o
r
b
y
l
o
P
%
1
.
0
<
%
1
.
0
)
E
D
B
P
(
s
r
e
h
t
e
l
y
n
e
h
p
i
d
d
e
t
a
n
i
m
o
r
b
y
l
o
P
Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:
Examples of exempted components are:
1.
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (
≦
500 mm): maximum 3.5 mg per lamp.
(2) Medium length (
＞
500 mm and
≦
1,500 mm): maximum 5 mg per lamp.
(3) Long length (
＞
1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
