Viessmann Vitocell 340-M Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 32

Viessmann Vitocell 340-M Скачать руководство пользователя страница 24

24

Cleaning the inside of the DHW cylinder

1.

Drain the cylinder from the DHW
side.

2.

Disconnect the cylinder on the DHW
side from the pipework to prevent
cleaning agents and contaminants
entering the pipework.

3.

You can also carry out cleaning on
the DHW side with chemical cleaning
agents.

!

Please note

Never use cleaning agents
containing hydrochloric acid,
to prevent material losses.

Danger

Cleaning agent residues can
lead to

poisoning

.

Always observe the details
provided by the manufacturer
of the cleaning agent.

4. Fully

drain any cleaning agent.

5. Thoroughly

flush the indirect coil on

the DHW side after cleaning.

6.

Reconnect the cylinder to the pipe-
work.

7.

Fill the cylinder from the DHW side.

Instructing the system user

The installer must instruct the user in the
operation of the system.

Commissioning, inspection, maintenance

Further details regarding the individual steps

(cont.)

5719 714 UAE

«
...
22
23
24
25
26
...
»

Содержание Vitocell 340-M

































Отзывы:

Нет отзывов