background image

58

en-US/C

A

If, before the delay time has elapsed, the disinfection 
conditions are fulfi lled by solar loading, thermal disin-
fection is considered complete and a new monitoring 
period begins.
If the starting time is adjusted to 00:00 (factory set-
ting), the delay function is inactive.
When thermal disinfection is activated, different dis-
play channels appear depending on the current status 
of the function (see also p. 42):
CDIS - countdown of the monitoring period
DDIS - countdown of the disinfection period
TDIS - substitutes TSTT during the disinfection period
SDIS - displays the adjusted starting time (fl ashing) 

during the delay time after the monitoring pe-
riod has ended

 OTDIS / TSDIS

Sensor thermal disinfection
Adjustment range: 2,3,4,5
Factory setting: system dependent

For this function, free sensors at an appropriate posi-
tion can be selected.

 OTDIS / RDIS

Relay thermal disinfection
Adjustment range: 2, 3, 4
Factory setting: system dependent

The relay for the thermal disinfection function can be 
selected.

 Parallel relay

 OPARR / PARRE

Parallel relay
Adjustment range 2, 3, 4
Factory setting: 2

With this function, e. g. a valve can be controlled in 
parallel to the pump via a separate relay PARRE.
If solar loading takes place (R1 and/or R2) or if a solar 
function is active, the relay selected will be energized. 
The parallel relay can also be energized inversely 
(INVER).

Note 
If R1 and/or R2 are in the manual mode, the 
selected parallel relay will not be energized.

 Energy metering

 OHQM

Energy metering
Adjustment  range:  OFF / ON
Factory setting: OFF

 OHQM / FTYPE

Flow rate detection type
Selection:  1, 2

Factory setting

: 1

The energy metering can be carried out in 2 different 
ways (see below): without fl owmeter (using a fi xed 
fl ow rate value) or with a V40 fl owmeter. 

 

Î

Enable the energy metering option in the channel 
OHQM 

 

Î

Select the type of fl ow rate detection in the chan-
nel FTYPE

Flow rate detection type:
1 :  fi xed fl ow rate value 
2 :  V40

Содержание SCU345









































































Отзывы: