Viessmann B23 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 108

background image

106

Vitoladens 300-C, type BC3

We, Viessmann Werke GmbH & Co. KG, D-35107
Allendorf, declare as sole responsible body that the
named product complies with the European directives
and supplementary national requirements in terms of
its design and operational characteristics.

Using the serial number, the full Declaration of Con-
formity can be found on the following website:

www.viessmann.co.uk/eu-conformity

Manufacturer's declaration

This product meets the requirements of the Efficiency Directive (92/42/EEC) for

condensing boilers

.

The product characteristics determined as system values for the product

Vitoladens 300-C as part of EC type

testing according to the Efficiency Directive

(see specification table) can be utilised to assess the energy effi-

ciency of heating and ventilation systems in buildings to DIN V 4701-10, as specified by the EnEV [Germany].

Manufacturer's certificate according to the 1st BImSchV [Germany]

We, Viessmann Werke GmbH & Co. KG, D-35107 Allendorf, confirm that the product

Vitoladens 300-C oil con-

densing boiler

complies with the NO

x

limits specified by the 1st BImSchV paragraph 6 [Germany]:

Allendorf, 3 April 2019

Viessmann Werke GmbH & Co. KG

Authorised signatory Reiner Jansen
Head of Strategic Quality Management

Certificates

Declaration of conformity

6136330

Appendix

«
...
104
105
106
107
108
»

Содержание B23













































































































Отзывы:

Нет отзывов

Похожие инструкции для B23

Бренд: Beretta Страницы: 80

Senator RFB006 6kW

Бренд: Range Страницы: 32

Бренд: Viessmann Страницы: 32

Бренд: Riello Страницы: 148

Super Xpress SX iQ Series

Бренд: OSO HOTWATER Страницы: 28

Бренд: Maktek Страницы: 21

Бренд: Buderus Страницы: 52

Бренд: PEERLESS Страницы: 17

Бренд: PEERLESS Страницы: 30

Бренд: PEERLESS Страницы: 40

Бренд: Potterton Страницы: 48

Бренд: Potterton Страницы: 56

Бренд: Potterton Страницы: 60

Бренд: HTP Страницы: 8

SuperStor Ultra SSU-20B

Бренд: HTP Страницы: 8

Hydra Smart RT-199

Бренд: HTP Страницы: 73

Бренд: HTP Страницы: 81

Бренд: Sime Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды