background image

1 About these instructions for use

Trade mark rights exist for this document, further information can be
found at 

viega.com/legal.

1.1

Target groups

The information in this instruction manual is directed at the following
groups of people:

n

Heating and sanitary professionals and trained personnel

It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.

The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.

1.2

Labelling of notes

Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.

DANGER! 

This symbol warns against possible life-threatening injury.

WARNING! 

This symbol warns against possible serious injury.

CAUTION! 

This symbol warns against possible injury.

NOTICE! 

This symbol warns against possible damage to property.

Notes give you additional helpful tips.

About these instructions for use

Universal bracket

4 from  11

Содержание 8062.5












Отзывы: