background image

66550029-EN - V4.0 - 15/02/19

- 11 -

ESVK/6788 Series “2 wire Bus” videokit

ESVK/6788 Series - Installation handbook

Art. 4333/4333X 

 Speaker unit module with built-in functional to digital interface

FRONT LEDS SIGNALLING DESCRIPTION

When illuminated, indicates that it is not possible to make a call because a call or a conversation is in progress (from 

the outdoor station from which you are calling or from another outdoor station on systems with multiple entranc-

es). The LED will be off when the system is in stand-by,
If illuminated, indicates that the call from the outdoor station is in progress. The LED will switch OFF when the call 

is answered or after the programmed number of rings.

If illuminated, indicates that it is possible to speak because the call has been answered. The LED will switch OFF at 

the end of a conversation (or at the end of the conversation time).

If illuminated, indicates that the door lock has been operated. It will switch OFF at the end of the programmed 

“door opening” time.

PROGRAMMING

The programming consists of the following settings:

•  Unit ID (1..8);

•  Door Opening Time (1, 2, 5 or 10 seconds);

•  Conversation Time (1 or 2 minutes);

•  Addressing order of the buttons.

•  Main camera selection

The settings are carried out through the 8 way dip-

switch (reference 

J

 on 

Fig. 2

) accessible from the 

rear side of the module.

UNIT ID

Switches

ID

1

2

3

OFF OFF OFF

1

ON OFF OFF

2

OFF ON OFF

3

ON

ON OFF

4

OFF OFF ON

5

ON OFF ON

6

OFF ON

ON

7

ON

ON

ON

8

DOOR OPENING TIME

Switches

Seconds

4

5

OFF OFF

1

ON OFF

2

OFF ON

5

ON

ON

10

CONVERSATION TIME

Switch

Minutes

6

OFF

1

ON

2

ADDRESSES ORDER

Switch

Sort

Switch

Sort

7

7

OFF

1

2

8

9

10

11

12

3

4

5

6

7

EB2

EB1

ON

11

12

6

7

8

9

10

1

2

3

4

5

EB2

EB1

Art. 125 required. When Art. 125 is used, follow the directions in the diagram to supply the push buttons modules.

MAIN CAMERA SELECTION

Switch

Selection

8

OFF

Main camera internal

ON

Main camera external

MAXIMUM ILLUMINATION DISTANCE FROM CAMERA AT NIGHT

The illumination LED’s within the camera will illuminate the visitor when they are within 50 cm of the camera.

MAX 50 cm

Содержание ESVK Series









































Отзывы: