Videofied OMV-VX Скачать руководство пользователя страница 8

Disassembly

Reassembly

8

INSTALL SHEET

OMV-VX

 OUTDOOR VISUAL VERIFICATION DETECTOR

Sensitivity adjustment

The OMV-VX detector comes with the capability of adjusting the sensitivity level of the PIR. It can improve the 
detection or, on the contrary, reduce false alarms. Raising sensitivity will raise detection range, the detection field 
will be larger and smaller thermal signatures will be detected. You should only use this feature when the site has 
been diagnosed as needing this adjustment. It cannot be used to optimize detection as the adjustment may be too 
high and generate either false alarms or missed intrusions.

Examples : Plant growth, pets.

Please note that the detector must be installed to prevent intrusions (aim the detector towards an access point), 
sensitivity adjustment will have no effect if the installation doesn’t comply with the installation recommendations 
described in this document.

Adjust sensitivity for the OMV-VX MotionViewer

To change the OMV-VX sensitivity, you need to change the 

detector name

:

DEVICE

CONFIGURATION

CHANGE NAME 

DEVICE

OK 

or 

YES

To select the OMV-VX

OK 

or 

YES

SENSITIVITY 

ADJUSTMENT

MINIMAL 

SENSITIVITY

detector_name

$2

LOW SENSITIVITY

detector_name

$1

DEFAULT 

SENSITIVITY

detector_name

HIGH SENSITIVITY

detector_name

$8

MAXIMAL 

SENSITIVITY

detector_name

$9

Enter the detector name then enter 
the 

$

 symbol at the end and the 

chosen digit (without space). The 
number following $ will depend on 
the necessary adjustment:

$ Symbol

CMA keypad

 : Press @ repeatedly 

until $ is displayed

XMA/XMB keypad

 : Press 

1

 

repeatedly until $ is displayed

Masking lens

The OMV-VX detector is provided with a masking kit. With this kit you 
can inhibit specific zones in the detection field because elements in 
those zones can generate false alarms, like a tree or a road.  

After disassembling the detector, detach the precut elements from 
the kit and place them directly behind the lens at the detection beam 
location you wish to mask.

Once it is done, put the OMV-VX elements back together as shown 
below. 

Содержание OMV-VX












Отзывы: