vidaXL 140285, Руководство по эксплуатации и технике безопасности

Страница: 59 / 128

59 EN___User manual |
the outlet, so you can connect air hoses of different sizes.
2. The original air hose has rubber airproof film on the inside;
the user can make it airtight manually, to ensure a good
performance. If the air hose used is not the original, the air
hose and air compressor may not be airtight. However, a
100% level of airtightness is only needed for auto stop
function air compressors. Seal thread tape can be used to
prevent leakage. This elastic tape is readily available in DIY
stores.
3. Connect the air compressor, air hose and airbrush (or other
air tools), plug the unit into the mains, turn on the switch,
then the air compressor will start operating. The pressure
gauge will show the maximum pressure, and you can adjust
the working pressure by adjusting the pressure adjustor.
4. Check for air leakage. Please do not use any air tools before
the compressor reaches the maximum pressure and
observe whether the auto-stop will engage. If the auto-stop
does not engage, please turn off the switch, and check the
index on pressure gauge. If it is very steady, this means the
seal is airtight; if the index declines quickly, this means
there is air leakage around the connection. Please check
and make it airtight, because any small leakage will affect
the performance of the compressor. (It may lead to
frequent engaging of the auto-stop and auto-start).
5. There is a difference between maximum pressure and
working pressure. The compressor’s maximum pressure is
the highest possible pressure, and the working pressure is
the one shown on the pressure gauge when the connected
airbrush is used. The working pressure is the constant
pressure the compressor can maintain during airbrushing.
The level of this working pressure depends on the nozzle
diameter of the airbrush to which it is connected; the larger
the nozzle diameter, the bigger the amount of air which can
escape and the lower the compressor’s working pressure.
6. The compressor’s tank can store compressed air before use
with the airbrush (or other air tools). The tank is very
useful, the advantages are as follows:
a) The tank provides a reservoir of pressurized air that you
can call during use.
b) You can use air at a regulated pressure from the tank
instead of the average pressure of the piston cylinders.
c) Because you’re drawing air from the tank, variations in
the air supply caused by the physical motion of pistons
pressurizing air are eliminated .
d) Longevity of compressor engine increases because it
builds up only the needed pressure for the tank instead
of always being on.
e) Tanks are great first line moisture traps.
3.1 Model BD air bursh
1. Fill the cup with properly thinned fluid.
2. Hold the airbrush lightly in your hand.
3. By pressing the main lever, a stream of air emerges. Draw it
backwards gradually for color atomization.
4. The spray pattern is in accordance with the distance
between the work surface and air brush.
5. For fine line spraying, remove the needle cover and hold
the air brush close to the work surface.
4 Additional information
4.1 Features and functions
Air tank ensuring steady air flow without variations.
Air pressure gauge; air filter; pressure adjustable.
Piston type: Oil free and not air polluting.
Continuous, powerful pressure from the onset.
Auto start and auto stop function.
Thermally protected.
Low noise: 47dB.
Safety device for air tank.
4.2 Model bd air bursh applications
Commercial arts, illustrations, photo retouching, hobby and
crafts.
5 Maintenance and cleaning
5.1 Trouble Shooting
Problem Possible cause Likely Solutions
The motor does not
work.
No electrical power Plug the power cord into a working, 220V-240V~, grounded,
electrical outlet.
Damaged power cord. Have a qualified service technician replace the power cord.
Electrical wiring within the unit is
defective.
Have a qualified service technician replace the electric
wiring.
Power switch is defective. Have a qualified service technician replace the power
switch.