Victron energy BlueSolar 100/30 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 61

background image

The system electrical negative should be bonded through a GFPD to earth ground at one (and only one) location.

When a ground fault is indicated, battery terminals and connected circuits may be un-grounded and
hazardous.

4.5. Electrical connections

Make all electrical connections in the following order:

• Confirm correct battery polarity, then connect the battery (this will allow the solar charger to recognize the system voltage).

Torque moment 1.6Nm.

• Connect the VE.Direct communication cable (if applicable).
• Confirm correct PV polarity, then connect the solar array.

Torque moment 1.6Nm
If accidentally connected in reverse polarity, the PV voltage will drop and the controller will heat up but will not charge the
battery.

• In case a MPPT WireBox is used:

First: Secure all electrical cables as indicated in the WireBox installation instructions
Then: Place the WireBox plastic cover over the solar charger connection area and secure it.

See below figure for an example of the solar charger connections:

DC loads

4.6. Connect the MPPT Control display

Connect the (optional) MPPT Control display to the VE.Direct port of the solar charger using a VE.Direct cable.

Note that it is not possible to extend the VE.Direct cable, the maximum length can not exceed 10 meter.

For more information, see the

MPPT Control display manual

MPPT solar charger manual

Page 11

Installation

«
...
13
14
15
16
17
...
»

Содержание BlueSolar 100/30






























































Отзывы:

Нет отзывов

Похожие инструкции для BlueSolar 100/30

Бренд: Kärcher Страницы: 96

Бренд: ULTIMATE SPEED Страницы: 190

NovaChat Series

Бренд: Saltillo Страницы: 296

ChargePlus Flex

Бренд: S.P.E. Страницы: 16

Бренд: Gallagher Страницы: 64

Бренд: Laser Страницы: 2

Mobile Black T2

Бренд: Nexxtender Страницы: 17

Бренд: Anywhere Cart Страницы: 12

EVERVOLT EV-BMS

Бренд: Panasonic Страницы: 30

Бренд: Wiha Страницы: 136

Бренд: Pitaka Страницы: 20

Бренд: Chauvet DJ Страницы: 8

Бренд: Motorola Страницы: 76

PMLN6394 Series

Бренд: Motorola Страницы: 28

Бренд: Motorola Страницы: 52

Бренд: Motorola Страницы: 60

Бренд: Motorola Страницы: 4

Бренд: Motorola Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды