Victoria-05 Ltd.
8
The ash from the combustion process is conducted in an ashtray underneath the combustion chamber. The ashtray must be
periodically cleaned by pouring in a metal container or by a vacuum cleaner, but only when the pellet stove is cold.
Through built-in circulating pump position (J) of (Fig.2.1), hot water passes from the integral boiler to the heating system. The
filling and emptying of the heating system is carried out via a shut-off valve, which has to be assembled outside. The system
pressure is controlled by a manometer, which has to be assembled outside.
The pellet stove is designed to operate with a built-in closed expansion vessel (H) and a pressure valve.
High efficiency and low emissions of the pellet stove is guaranteed by an electronic control system that manage the amount of
the fuel, the flue gases conduction, supplying of the combustion air and operation of the circulating pump. The control panel of
the control system is placed in the backside on the top panel of the pellet stove position (G) in (Fig.2). Through the control panel
can visualize and manage all stages of the operation of the pellet stove.
8.
Fuel.
Pellet stove e designed and programmed to burn wood pellets. They have a cylindrical shape and they are made of compressed
by a high-pressure timber, without adhesive and additive materials. The wood pellets are sold in packages weighing 15 kg, which
facilitates their storage. Better combustion, the wood pellets must be stored in dry and ventilated area. Pellet stove is designed,
developed, programmed and tested to operate with wood pellets class A1, according to EN plus and BS EN ISO 17225-2: 2014
with the following parameters:
Maximum diameter:
Ø 6 mm
Maximum length:
25 mm
Maximum moisture content:
8 %
Maximum ash content:
0.5%
Minimum calorific value:
4300 ccal/kg
Good quality wood pellets ensure good combustion and low emissions into the atmosphere.
The use of wood pellets with a
lower quality
results in a need for more frequent cleaning of the combustion chamber, reducing
heat output and efficiency. They are increasing the fuel consumption sensitively. Inadequate wood pellets can cause blockage of
the auger and to stop the operation of the pellet stove.
IF PELLET STOVE BLOCKED, THE REASON WILL APPEAR ON THE DISPLAY AND IT WILL BE SAVED.
Using low quality wood pellets or non-manufacturer recommended above may compromise the operation of the
pellet stove and lead to termination of the warranty. Pellet stove should not be used to burn other types of fuels or
materials. Invalid guarantee!
9.
Appliance installation.
Trained and competent technicians or companies must perform installing of the pellet stove and heating system! The
manufacturer does not warrant the operation of the heating system, but for pellet stove only. Qualified technicians
should perform all activities in inspection and repair of electrical components. Switch off the pellet stove from the
grid-circuit before any inspection or repair!
Refer to the regulations valid for the country, where will be used the pellet stove, if you do not find the information you are
interested in this instruction manual.
Not recommended installing a pellet stove in rooms where there is mounted another heater. If it does, it must be equipped with
a separate air duct.
Compatibility with other devices:
Pellet stove should not be installed in the same room in which there absorbers and / or devices that reduce ventilation in the
room.
Checking electrical connections:
Pellet stove is equipped with a power cable to be connected to a voltage 230V / 50Hz. Changes exceeding by 10% the voltage
can damage the appliance. Grid-circuit must comply with the provisions of the laws and requirements for grounding. According
to the requirements for grid-circuit connection, pellet stove should be installed so as to ensure free access to the plug and socket
(230V / 50Hz). According to the safety requirements prohibited the room in which is mounted pellet stove to an electrical
installation that is located on the floor. Lack of bonding / grounding can cause damage for which the manufacturer is not
responsible.
Positioning:
To operate well, the pellet stove should be leveled. The floor on which is placed the pellet stove must be of non-combustible
materials (concrete, terrazzo, marble, terracotta, etc.).
Given the easy servicing and refueling, we recommend the following minimum free distance around the pellet stove: 1000 mm
in front, back and sides -500 mm, top -minimum 1000 mm.
