manualshive.com logo in svg

Victaulic I-W07, Руководство по установке, Страница: 3 / 8

Поделиться
Скачать
Victaulic I-W07 Скачать руководство пользователя страница 3

INSTALLATION INSTRUCTIONS – 

14 – 24-INCH/355.6 – 610.0-MM SIZES

THIS COUPLING ASSEMBLY HAS A TORQUE REQUIREMENT. REFER 
TO THE INSTRUCTIONS IN THIS SECTION OR THE MARKINGS ON 
THE HOUSINGS FOR THE SPECIFIC TORQUE REQUIREMENT.
1. 

Prepare the pipe by following the “Pipe Preparation – All Sizes” 
section on page 2.

2.

  Check the gasket to make sure it is suitable for the intended 

service. The color code identifies the gasket grade. Apply a thin 
coat of Victaulic lubricant or silicone lubricant to the gasket lips 
and exterior.

3.

  Position the gasket over the pipe end. make sure the gasket does 

not overhang the pipe end.

4.

  Align and bring the two pipe ends together. Slide the gasket into 

position, and center it between the grooves in each pipe.

5.

  Apply a thin coat of Victaulic lubricant or silicone lubricant to the 

bolt threads.

6.

  Install the housings over the gasket. make sure the housings’ 

keys engage the grooves completely on both pipes. Support the 
segments while preparing to install the bolts and nuts.

6a.

  Install the bolts, and thread the nuts finger-tight onto the bolts. 

NOTE:

 make sure the oval necks of the bolts seat properly in the 

bolt holes.

I-W07/W77_3

I-W07/W77

INSTALLATION INSTRUCTIONS

www.victaulic.com

VICTAulIC IS A ReGISTeRed TRAdemARk oF VICTAulIC ComPAny. © 2009 VICTAulIC ComPAny. All RIGhTS ReSeRVed. PRInTed In The uSA.

REV_E

Couplings

 STYLE W07 RIGID AND 

 STYLE W77 FLExIBLE

Содержание I-W07









Отзывы:

Нет отзывов