background image

 

 

1

VWG-40 

Viconics Wireless Gateway 

Hardware Installation Guide 

(Issue Date September 24, 2008 – 028-0179 R8) 

Product overview  

 

 

 
The VWG-40 and related wireless thermostats are targeted to retrofit applications where the 
addition of communicating field bus wiring within the building space is prohibitive. The 
Gateway and Communicating Thermostats with wireless field bus encourages the use of 
existing wiring utilized by existing electronic thermostat type controls.  
 
 
The VWG-40 when utilized in conjunction with the VT7xxxXxxxxW series wireless thermostats will offer the integrator 
simple BACnet IP or BACnet MS/TP objects to integrate over standard building automation systems using familiar 
integration toolsets. 
 
A maximum of 30 wireless thermostats can be wirelessly attached to a single VWG 
 
The following additional documentation is available on www.viconics.com 

• 

Gateway BACnet integration guide (VWG-40-IP & VWG-40-MSTP), is available in document ITG-VWG-40-BAC-Exx 

• 

Information on design consideration of wireless mesh networks and VWG set-up / diagnostics is available in document LIT-
VWG-40-SETUP-Exx 

 

Part available  

 

 

 

Part number 

Description 

VWG-40-IP-1000 

Viconics BACnet over IP wireless gateway. Includes: 

-  Supports up to 30 wireless thermostats 

Factory mounted wireless adapter 

24 Vac panel mounted power supply 

Gateway mounted antenna 

VWG-40-MSTP-1000 

Viconics BACnet RS485 MS-TP wireless gateway. Includes: 

-  Supports up to 30 wireless thermostats 

Factory mounted wireless adapter 

24 Vac panel mounted power supply 

Gateway mounted antenna 

VWG-40-LON-1000 

(Upcoming) 

Viconics LON wireless gateway. Includes: 

-  Supports up to 30 wireless thermostats 

Factory mounted wireless adapter 

24 Vac panel mounted power supply 

Gateway mounted antenna 

VWG-APP

 

Interface software for VWG configuration and set-up. Operates under Windows XP 

Uses a LAN crossover IP connection for initial set-up. 

VWG-RA

 

Remote antenna for gateway when the gateway is installed inside a metal cabinet or 
when remote antennal mounting is required by physical installation 

VWG-WA

 

Replacement antenna for gateway mounted antenna setup 

VWG-PS-DC

 

24 Vac to 15 Vdc panel mounted power supply for VWG 

VWG-PS-AC

 

120 Vac to 15 Vdc power supply for VWG with cord 

VWG-BB

 

Replacement battery backup pack for the VWG 

 
Trademarks  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Niagara, Niagara AX is a registered trademark of Tridium, Inc. 
LON, LonWorks and LonTalk are registered trademarks of Echelon Corporation 
BACnet is a registered trademark of ASHRAE 

 

Содержание VWG-40














Отзывы: