background image

FCC Notice 

Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart 

B for a Class A digital device. 

 

WARNING 

 
This equipment generates and uses radio frequency energy and if not installed and used 
properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference 
to radio and television reception. It has been type tested and found to comply with the limits for a 
Class A computing device in accordance with the specification in subpart B of part 15 of the FCC 
rules, which are designed to provide reasonable protection against such interference in a 
commercial installation. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause interference to radio and television reception, 
which can be determined by turning equipment off and on, the user is encouraged to try and 
correct the interference by one or more of the following measures: 
 

 

Reorient the receiving antenna. 

 

Relocate the equipment with respect to the receiver. 

 

Relocate the equipment away from the receiver. 

 

Plug the equipment into a different electrical outlet so that the equipment 
and receiver are on different branch circuits. 

 
If necessary, the user should consult the dealer or an experienced radio/television technician for 
additional suggestions. 
 
The user may find the following booklet prepared by the Federal Communications Commission 
helpful: 
 

“Interference Handbook, Bulletin CIB-2” 

 
This booklet is available from the U.S. Government Printing Office, Superintendent of Documents, 
Mailstop SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1. 
 

Warning: Power must be removed from this unit before removing circuit modules or cables. 

 

Caution: This unit contains circuit cards with integrated circuit devices that can be damaged 

by static discharge. Take all necessary precautions to prevent static discharge. 

 

Содержание VM-6215LED





























Отзывы: