Vicon VC5000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 20

Vicon VC5000 Скачать руководство пользователя страница 17

TROUBLESHOOTING

Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, contact
Vicon. See

Shipping Instructions

on page

3

.

No picture on the monitor screen

•

Is the power turned on to all connected devices? Is the voltage correct?

•

Are all the signal connecting cables correctly connected?

•

Is the lighting sufficient?

•

Has the lens cap been removed?

•

Is the lens type (

DC

or

VIDEO

) correctly selected?

Depending on the type of lens, the

A. I. LENS

switch must be set accordingly.

•

Is the iris control correctly set?

The picture is not clear

•

Is the monitor correctly adjusted?

•

Is the flange-back position correctly set?

•

Is the lens focus correctly adjusted?

•

Are the lens surfaces clean?

If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens
cleaning set.

VC5000-DSP GB 2002, 8, 7

16

English

«
...
15
16
17
18
19
...
»

Содержание VC5000





















Отзывы:

Нет отзывов