Vicon Andex 353 Скачать руководство пользователя страница 48

Страница: 48 / 74

Preparations on the field

Adjusting the swath

former

The swath former is folded into the correct position when changing
from the transport to the work position.

Adjusting the swath

former's direction of

travel

It is possible to adjust the direction of travel of the swath former as
follows:



Remove the bolts.



Move the swath former into the desired position.



Fit the bolts and tighten them in the new position.

Adjusting the swath

former's height

It is possible to adjust the height of the swath former as follows:



Loosen the screws.



Adjust the height of the swath former.



Tighten the bolts in the new position.

Adjusting the swath

width

The swath width can be adjusted as follows:



Release the clamping lever on the swath former.



Pull out or push in swath former to the desired width.



Refasten and secure the clamping lever.

Swath former

Bolts

Swath former

Bolts

Clamping lever

Содержание Andex 353











































































Результаты поиска

Содержание Andex 353

Отзывы:

Похожие инструкции для Andex 353

Бренды по названию

Популярные бренды

Vicon Andex 353, Руководство по эксплуатации

Результаты поиска

Содержание Andex 353

Отзывы:

Похожие инструкции для Andex 353

Бренды по названию

Популярные бренды