Vibe DSX11 Скачать руководство пользователя страница 4

Страница: 4 / 12

2. Setting Rudder Servo Direction (REVERSE SWITCHES)

① Switch over to 「FUNCTION LIST」 by pressing the

【ENT】 key, turn the dial and select 「REVERSE SW」

then press the dial again.

② Turn the dial to 「RUDD」and reverse as necessary.
　Return to 「FUNCTION LIST」 by pressing the【LST】

key.

3. Setting TRAVEL ADJ. Values

① Turn the dial to select「TRVL ADJ.」and press the

dial.

② Turn the dial to select each item and press the dial

to change each in turn.

③ Turn the dial to shift to each item and input the

number as shown in the figure.

※「Use the appropriate control stick to switch

between H/L, U/D or L/R.

④ Press the【ENT】key to return to regular screen.

Setting for other models of Radio set.

※ 1 If you use a transmitter other than the JR DSX11 (or the XG8 described below), please refer to the

manufactures instruction manual, in combination with the helicopter assembly manual.

※ 2 Please refer to your tail gyro instruction manual for advise on tail rotor setup and initial transmitter

settings.

※ 3 If you are using a FBL system other than the TAGS01, please refer to your FBL system manual.

※ Note: The rudder reverse switch direction will depend
on the servo and gyro/FBL unit used. Please refer to
your gyro/FBL unit instruction manual for further details.

※ Note that the 「THRO」 direction and travel adjust
settings will depend on the ESC used.

③ Input the number

① Select「REVERSE SW」

① Select「TRAVEL ADJ.」

①

② , ③

② Select item

P.4

① , ④

② , ③

Содержание DSX11













Результаты поиска

Содержание DSX11

Отзывы:

Похожие инструкции для DSX11

Бренды по названию

Популярные бренды

Vibe DSX11, Руководство по настройке

Результаты поиска

Содержание DSX11

Отзывы:

Похожие инструкции для DSX11

Бренды по названию

Популярные бренды