ViaSat SurfBeam 2 Скачать руководство пользователя страница 13

Страница: 13 / 66

SurfBeam® 2 Pro Portable Terminal Operations Guide

Page 2-6

ViaSat Proprietary Information

2.3.3

Assembling

After performing the site survey (review section 2.1 before starting the process below), the user can now unpack,
assemble, and deploy the unit. Table 2-2 provides the instructions on this process.

Table 2-2: Unpack and Assembly Process

Step

Action

Image

Perform a site survey to locate your unit’s deployment location.

Open the transit case on a flat surface to see the top layer of the
case’s components.



Tripod



Azimuth/Elevation Assembly



Center Reflector

Remove the Tripod from the pocket on the right side of the case
and loosen all knobs to arrange each leg in its out-most position.

Tighten each knob (x3) to lock the Tripod’s legs and position the
Tripod with one leg pointing north.

Remove the Azimuth/Elevation Assembly from the pocket on the
left side of the case.

Looking at the base of the Assembly, loosen the Azimuth lever
and knob.

Содержание SurfBeam 2



































































Результаты поиска

Содержание SurfBeam 2

Отзывы:

Похожие инструкции для SurfBeam 2

Бренды по названию

Популярные бренды

ViaSat SurfBeam 2, Руководство по эксплуатации

Результаты поиска

Содержание SurfBeam 2

Отзывы:

Похожие инструкции для SurfBeam 2

Бренды по названию

Популярные бренды