manualshive.com logo in svg

Vetus M4.15 SOLAS, Руководство по эксплуатации, Страница: 17 / 80

Поделиться
Скачать
Vetus M4.15 SOLAS Скачать руководство пользователя страница 17

15

Fuel

Ensure that the fuel tank is filled with diesel 
fuel.
Use only clean, water-free, commercial 
approved diesel fuel.
For fuel grade see page 64.
Bleed the fuel system, see page 26.

Other preparations

•  Check battery and cable connections.

•  Start the engine, see page 16, and let it 

run for about 10 minutes without load.

  Check the engine and all connections 

(fuel, cooling water and exhaust) for 
leaks.

Running-in

In order to ensure a long life for your 
engine, please observe the following for 
the first 50 operating hours:

•  Allow  the  engine  to  reach  operating 

temperature before applying a load.

•  Avoid fast acceleration.
•  Do  not  allow  the  engine  to  run  faster 

than 3/4 of maximum RPM.

First commissioning
Running-in

Use

FUEL

VD00002

Never fill the fuel tank while 
the engine is running. Do not 
spill fuel. Prevent unneces-
sary pollution.

Содержание M4.15 SOLAS

















































































Отзывы:

Нет отзывов