Vetus M2.02 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 120

background image

Lead seal

Maximum speed

adjustment screw

Minimum speed

adjustment screw

71

6 Maintenance

Checking engine speed

At full load (with the boat cruising) the maxi-
mum engine speed should be about 3,000
resp. 3600 RPM (see technical data page

101

).

If the engine does not reach this speed, it is
being overloaded!
If this is the case, check the ship’s propeller for
defects or irregularities, and also to see that it
is the correct pitch and diameter.

56 Adjusting engine idling speed

If the engine speed differs from that stated
above, it must be adjusted.
The engine idling speed can be reset using
the adjustment screw on the fuel pump.

55 Checking engine speed

The engine idling speed should be 850 rpm.

• Allow the engine to warm up normally (un-

til the coolant temperature reaches at least
60°C (140°F).) before checking and/or ad-
justing the idling speed.

• Check the engine RPM using a rev. counter,

or use the rev. counter fitted to the control
panel.

W

arning

The maximum engine speed adjust-
ment screw has been correctly set at
the factory and sealed. DO NOT at-
tempt to remove this seal.

10

VD00134

VD00931

«
...
71
72
73
74
75
...
»

Содержание M2.02

























































































































Отзывы:

Нет отзывов

Похожие инструкции для M2.02

Бренд: BAFANG Страницы: 4

Бренд: Quick Fuel Technology Страницы: 5

Бренд: Kohler Страницы: 4

Бренд: ALL POWER AMERICA Страницы: 28

Бренд: Jenny Science Страницы: 9

MaxxForce DT 10

Бренд: Navistar Страницы: 109

Бренд: ABB Страницы: 215

7-1/2 HP 212cc OHV

Бренд: Power Fist Страницы: 52

Бренд: SSANGYONG Страницы: 14

Бренд: NACIONAL MOTOR Страницы: 43

Бренд: Farymann Diesel Страницы: 110

Бренд: LinMot Страницы: 54

Бренд: LinMot Страницы: 79

Бренд: Toyota Страницы: 625

Бренд: A.O. Smith Страницы: 52

Бренд: SKY Engines Страницы: 26

Бренд: TOHATSU Страницы: 89

Бренд: Danfoss Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды