Rev. 6/21/2019
WTJ-HITCH MANUAL
Copyright 2019 Vestil Manufacturing Co.
Page
3
of
9
Hazards:
We strive to identify all hazards that could occur while using our products, but no manual can address every
risk. The most effective way to avoid injury is to exercise sound judgment whenever using this device and to read
the entire manual carefully before installing, using, or servicing the product. Vestil recommends that you contact
(the “TSD”) if you have any questions about instructions in the manual. We
intend to provide our customers with the best instructions possible and encourage you to contact the TSD if you
believe that a necessary instruction is missing or incomplete
.
Improper or careless operation might result in serious personal injuries sustained by the operator
and bystanders. Always apply material handling techniques learned during training and use the product properly.
•
Failure to read and understand the entire manual before assembling, using or servicing the product
constitutes misuse
.
Read the manual to refresh your understanding of proper use and maintenance
procedures as necessary.
•
DO NOT drive with the crane fully assembled. Disconnect at least the upper assembly (post + boom +
boom brace) from the base frame before driving the vehicle.
•
DO NOT use the crane unless it is in normal operating condition. Inspect the unit as described in the
instructions on p. 8 to determine whether it is functioning normally. DO NOT use the crane unless it passes
every
part of the inspection or until it is restored to normal operating condition.
•
DO NOT use a malfunctioning crane. Always perform the
(described on p. 7) before each use.
•
DO NOT attempt to lift a load that weighs more than the uniform capacity of your unit. The capacity appears on
label 287 as shown in “Label placement diagram” below. (Also see
•
DO NOT adjust crane angle while lifting a load. ALWAYS unload the crane before
described on p. 7.
•
Always watch the load carefully while raising, lowering and rotating it.
•
DO NOT stand beneath or travel under the crane if a load is suspended from it and DO NOT permit any person
to stand beneath or travel under the load.
•
DO NOT climb on the crane or the load.
•
This crane is designed for material handling ONLY. DO NOT use the crane to lift people.
•
ALWAYS load the crane properly. See
on pp. 7-8. Failure to properly position the crane and/or
the load might result in serious injury to the operator or bystanders.
•
DO NOT perform maintenance on this crane UNLESS it is unloaded and stably supported. If repairs are
necessary, ONLY install manufacturer-approved replacement parts.
•
The post of the crane (see item no. 5 on
) should rotate smoothly. Watch for binding or jerky movement and
listen for unusual noises. Remove the unit from service if you observe anything abnormal.
•
DO NOT use the crane UNLESS all labels are in place and readable. See
•
DO NOT modify this product in any way. Modifying the crane automatically voids the
9) and might make it unsafe to use.
Proper use and maintenance are essential for this product to function properly.
•
Always use this product in accordance with the instructions in this manual and consistent with any training
relevant to rigging used in conjunction with this product.
•
Periodically lubricate pivot points.
•
Keep the product clean & dry.
•
Only use approved replacement parts. To order replacement parts for this equipment, contact the factory.
Labeling diagram
:
Each pair of extensions should be labeled as shown in the diagram. However, label content and location are
subject to change so your product might not be labeled exactly as shown. Replace all labels that are damaged,
missing, or not easily readable (e.g. faded). To order replacement labels, contact the technical service and parts
http://www.vestilmfg.com/parts_info.htm
. Alternatively, you may request replacement parts
and/or service by calling (260) 665-7586 and asking the operator to connect you to the Parts Department.
A:
Label 586 (on one side of boom)
D:
Label 287 (on side
of post)
C:
Label 983 (on other side of boom)
B:
Label 208 (top of boom brace)
A & C
B
D
