background image

 

1

Hand Pallet Truck 

Note: 

Owner and operator MUST read and understand this 

operating instructions before use this pallet truck. 

 

Thank you for choosing our pallet truck. For your safety and correct operation, please carefully read 

the manual before use. 

 

NOTE:

  All of the information reported herein is based on data available at the time of printing. The 

factory reserves the right to modify its own products at any time without notice or incurring in any 

sanction. Please verify with the factory for possible updates. 

 

1. GENERAL SPECIFICATIONS

 

Capacity (lbs.) 

4,000 

Max. Fork Height  

6” 

Min. Fork Height  

1 7/8” 

Fork Length  

48” 

Overall Fork Width 

20”/27”/33” 

Load Wheel Diameter  

Ø1 ¾” x 3 5/8” Steel – 6003 2RS 

Steering Wheel Diameter 

Ø6 ¼” x 2” Poly on steel – 6204 2RS

Net Weight 

228/270/300 

 

 

2.  TO ATTACH HANDLE TO PUMP UNIT

 

2.1 Remove 3 bolts (D611) from the handle bracket (D151). 

2.2 Set handle (D610A, D610B or D610AS) on the bracket (D151), notice to allow the chain (D612) 

and the adjusting bolts (D614) assembly to pass through the hole in the center of the bracket (D151) 

and shaft (D153). 

2.3 Insert the 3 bolts (D611) through the handle into the bracket (D151), then tighten them securely. 

2.4 Raise the lever plat (D132) and insert the adjusting bolt (D614) into the front slot, keeping the 

adjusting nut (D615) on the under side of the lever plat (D132). 

 

3. TO ADJUST RELEASE DEVICE

 

On the draw-bar of this pallet truck, you can find the control handle (D608 or D608S) which can be 

regulated in three positions: 

   Raise                 - handle down 

   Drive position    - handle in center position 

Lower                - handle up, the lever moves back the drive position when released. 

If however they have been changed, you can adjust according to following step: 

3.1 If the forks elevate while pumping in the 

DRIVE 

position, turn the adjusting nut (D615) on the 

adjusting bolt (D614) or adjusting screw (D133) clockwise until pumping action does not raise the 

forks and the 

DRIVE 

position functions properly. 

3.2 If the forks descend while pumping in the 

DRIVE 

position, turn the nut (D615) or adjusting screw 

Содержание PM4-LP Series










Отзывы: