background image

Table of Contents

 

Rev. 10/25/2021 

CART-CTD, MANUAL 

Table of Contents

 

Copyright 2021 Vestil Manufacturing Co. 

Page 

3

 of 

13

 

 

SAFETY INSTRUCTIONS 

Vestil strives to identify foreseeable hazards associated with the use of its products. However, no manual can 

address every conceivable risk. The most effective way to avoid injury is to exercise sound judgment when 

assembling, using, inspecting, and maintaining this crane.  

 

      WARNING 

Risks of serious personal injuries or death.   

 

Failure to read and understand the entire manual before assembling, using or servicing the product 

constitutes misuse

.

 Read the manual to refresh your understanding of proper use and maintenance 

procedures as necessary. 

  DO NOT attempt to lift a load that weighs more than the capacity of your cart. The capacity appears on label 

287 as shown i

LABELING DIAGRAM

 on p. 10. Also see 

SPECIFICATIONS

 on p. 2. If the capacity displayed 

on label 287 differs from information on p. 2, the number shown on the label should be regarded as correct. 

  DO NOT allow people to stand or sit on either the cart or the load. 

  Stand clear of the cart while raising or lowering the tabletop. 

  Keep clear of pinch points while the deck rises and lowers.  

  DO NOT reach through the legs or crawl under the tabletop unless the tabletop is supported by maintenance 

prop(s). 

  DO NOT use the cart in corrosive environments.  

  ONLY use the cart on compacted, improved surfaces capable of supporting the combined weight of the cart 

plus a maximum rated load. 

  DO NOT perform maintenance on this cart UNLESS it is unloaded and maintenance stops are in place. If 

repairs are necessary, ONLY install manufacturer-approved replacement parts. 

  Center and evenly distribute loads on the tabletop. Secure loads to the tabletop if they are likely to roll or slide. 

  DO  NOT use the cart  unless it is in normal  condition.  Inspect the unit before each use according to the 

INSPECTION

 instructions on 

p. 9

-

10

 to determine whether the unit is functioning normally.  DO NOT use the 

cart unless it passes 

every

 part of the inspection or until it is restored to normal operating condition. 

  ALWAYS observe the cart while raising and lowering the tabletop. It should rise smoothly and evenly from side-

to-side. Watch for binding or jerky movement and listen for unusual noises.  Tag the unit "Out of order" and do 

not use it if you observe anything abnormal. 

  Always watch the load carefully while raising and lowering the tabletop. 

  DO NOT continue to press the UP button if the tabletop is fully elevated (does not continue to rise). 

  Before leaving the cart unattended, unload it and relieve hydraulic pressure by pressing the DOWN button and 

holding it until the tabletop is fully lowered. 

  DO NOT use the cart UNLESS all labels are in place and readable. See 

LABELING DIAGRAM

 on 

p. 10

. 

  DO NOT modify this product in any way. Modifications automatically void the limited warranty and might make 

the cart unsafe to use. 

NOTICE

 

Proper use and maintenance are essential for this product to function properly. 

  Turn the power unit off whenever the cart is stopped or otherwise not in use to preserve battery charge. 

  Batteries should be kept at full charge when the cart is stored for prolonged periods. Maintain battery charge by 

plugging in the charger. If the cart will be out of use for longer than 3 months, remove the batteries and store 

them in a cool, dry location. 

  Do not use this cart in damp/wet environments. The motor and controller are not sealed. 

  Periodically lubricate moving parts. 

  Keep the product clean & dry. Do not store this cart where it is exposed to the elements. 

  Only use approved replacement parts. To order replacement or spare parts for this equipment, contact the 

technical service department. 

Содержание CART-1000-2040-CTD














Отзывы: