VESTEL SMART 40PF7120, Руководство по эксплуатации

Страница: 37 / 60

English - 36 -
Switching On/Off
To Switch the TV On
Connect the power cord to a power source such as a
wall socket (220-240V AC, 50 Hz).
To switch on the TV from standby mode either:
Press the
Standby
button,
Pro/-
or a
numeric button on the remote control.
Press the side function switch on the TV until the TV
comes on from standby.
To Switch the TV Off
Press the Standby button on the remote control or
press the side function switch on the TV until the
TV switches into standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched into standby mode, the
standby LED can blink to indicate that features such as
Standby Search, Over Air Download or Timer is active. The
LED can also blink when you switch on the TV from standby
mode.
First Time Installation
When turned on for the first time, the language selection
screen is displayed. Select the desired language and
press OK.
On the next screen, set your preferences using the
navigation buttons and when finished, press OK to
continue.
Note: Depending on the Country selection you may be asked
to set and confirm a PIN at this point. The selected PIN cannot
be 0000. You have to enter it if you are asked to enter a PIN
for any menu operation later.
• The
Country
option should be selected as
Turkey
to make
TKGS(*) Installation available.
(*) TKGS(Türksat Kanal Güncelleme Sistemi) provides
options to install the satellite channel lists and keep them
up-to-date.
You can activate Store Mode option at this point. This
option is intended only for store use. It is recommended
to select Home Mode for home use. If Store Mode is
selected, a confirmation screen will be displayed. Select
YES to proceed. This option will be available in Other
Settings menu and can be turned off/on later.
If Home Mode is selected, Store Mode will not be
available after the First Time Installation . Press OK
button to continue.
Aerial Installation
If you select Aerial option from the search type selection
screen, the television will search for digital terrestrial TV
broadcasts. After all the available stations are stored, the
Channel List will be displayed on the screen.
While the search continues a message will appear, asking
whether you want to sort channels according to the
LCN(*). Select
Yes
and press
OK
to confirm
.
(*) LCN is the Logical Channel Number system that
organizes available broadcasts in accordance with a
recognizable channel sequence (if available).
Press
Menu button to quit channel list and watch TV.
Cable Installation
If you select
Cable
option and press
OK
button on the
remote control, a confirmation screen will be displayed.
Select
YES
and press
OK
to proceed. To cancel operation,
select NO and press OK . You can select frequency ranges
from next screen. Enter the frequency range manually
by using the numeric buttons. When finished, press OK
button to start automatic search.
Note: Searching duration will change depending on the
selected search step.
Satellite Installation
If you select Satellite option from the search type
selection screen, you can set a satellite and watch satellite
channels. When you select Satellite installation, Antenna
Type menu will be displayed. You can select Antenna
type as Direct , Unicable or DiSEqC switch .
Direct: If you have a single receiver and a direct satellite
dish, select this antenna type. After selecting Direct , another
menu screen will be displayed. Select an available satellite
and press OK to scan for services.
Unicable: If you have multiple receivers and a unicable
system, select this antenna type. Press OK to continue.
Configure settings by following instructions on the screen.
Press OK to scan for services.
DiSEqC switch: If you have multiple satellite dishes and
a DiSEqC switch , select this antenna type. After selecting
DiSEqC switch , another menu screen will be displayed.
You can set four DiSEqC options (if available). Press
GREEN button to scan all satellites or press YELLOW
button to scan only the highlighted satellite. To save and
exit press OK button.
TKGS installation
After the antenna type is selected and other satellite
settings are made, press the Red button to start
TKGS Installation . You can select to install HD or
SD channels during the installation. This selection
can be done later too using the
Preferred List
option
under the TKGS Installation menu. The selection will
be activated, after switching the TV off and back on
again or after a manual update as described below.
If wanted
TKGS Installation
can be applied manually
after the First Time Installation . Press the Menu
button. Highlight Settings and press OK . In the sub
menu highlight Satellite Settings and press OK .
Then select Antenna Installation . Then follow the
above mentioned steps to start a
TKGS Installation
.
Getting Started
First Time Installation - USB Connections