q
MAIN MIC LEVEL
Adjusts the input level of the MAIN MIC input.
w
MIC EQs
Adjusts the HI and LOW frequencies for both the
MAIN and SUB MIC input.
e
MIC PAN
Adjusts the panning for both the MAIN and SUB
MIC.
r
TRIM (PGM1/PGM2)
Adjusts the input level of each channel. For optimal
acoustic quality, set the INPUT FADER to a position
of 7 or 8 then adjust the TRIM so that a sufficient
signal is fed through the channel without distorting.
t
PGM EQs (PGM1/PGM2)
Adjusts the HI and LOW frequencies for each PGM
channel.
y
PGM BALANCE (PGM1/PGM2)
Adjusts the stereo balance for each PGM Channel.
Can also be used to adjust an unbalanced stereo image.
From a center position a clockwise rotation will
increase the volume of channel R over L. Whereas, a
Counter clockwise rotation will increase the volume of
channel L over R.
u
CROSSFADER REVERSE SWITCH
Reverses the action of the crossfader by switching
PGM1 and 2. Reverse mode, when on, is indicated
in the LED section.
i
MASTER LEVEL VOLUME
Adjusts the signal level outputs from LINE OUT.
o
CROSSFADER CURVE
Adjusts the crossfader curve. A clockwise rotation
gives a steep crossfader good for scratching and
cutting, whereas, a counter clockwise rotation gives a
gentle crossfader good for long running mixes.
!0
POWER LED
Lights up when the POWER SWITCH is on.
!1
INPUT SELECTOR
Used to select the input (LINE or PHONO) to be sent to each
PGM channel. The upper most position will select PHONO input.
This selector switch can also be used to perform for
TRANSFORMER SCRATCH. The operation direction of this
switch is selectable. To change the operational direction of this
switch remove the top panel and make the necessary the top panel.
!2
INPUT FADER (PGM1/PGM2)
Used to adjust the input level of each PGM channel. The Input
fader curve can be changed using a switch located on the unit
itself. This fader is a user replaceable unit. Ensure that you
replace with an IF-05PCV when it is worn out. For more
comprehensive instructions please refer to the "HOW TO
CHANGE THE FADER UNIT" section of this user guide.
!3
INPUT LEVEL METER
The LED level meters indicate the signal level of each
6
PGM channel.
!4
CROSSFADER
When the input levels of PGM1 and PGM2 are properly
set, PGM1 will be heard with the crossfader set to the left
side. PGM2 will be heard with the cross fader set to the
right side. When the crossfader is set in the center, both
programs will be heard. This is user replaceable fader
Replace with a "CF-PCV" when it is worn out.
!5
EFFECT RCV LEVEL
Adjusts the signal level input from an external effects unit
connected to the EFFECT RCV jacks on the front panel.
!6
EFFECT SEND LEVEL
Adjusts the signal level output to an external effects
unit connected to the EFFECT SEND JACK on the
rear panel.
!7
EFFECT SEND ON/OFF SWITCH
This switch is used to select the PGM to be sent to
EFFECT SEND JACK.
!8
MONITOR LEVEL
Adjusts the headphone monitor level.
!9
CF MONITOR
Crossfaders signal to be monitored from each program.
@0
MONITOR SELECT SWITCH
This switch is used to select the signal sent to the monitor
section. When set to CUE the signal heard is determined
by which PGM is being sent to the master and the location
of the Monitor Cross Fader
!9
. When set to MASTER you
will hear the master signal in the monitor section.
Содержание PMC-05PRO3VCA
Страница 1: ...OWNER S MANUAL...
Страница 5: ...5 F U N C T I O N S TOP PANEL...
Страница 10: ...10 CONNECTION...
Страница 12: ...Vestax Corporation JAN 2005 PMC 05Pro VCAE P N 4301 7102 2...