VESSER CGU12N, Инструкция по эксплуатации

Страница: 64 / 177

61
QSPEVDU
2 OUTDOOR UNIT INSTALLATION
2.1 Before Installation
‹ When the unit arrives, please check if any damage due to transport is existent. If any hurt is found on the
surface or inside, please declare to the transport company or the manufacturer in writing.
‹ Upon receipt of the unit, the unit and accessories shall be checked in accordance with the packing list.
Before acceptance, it must be confirmed that the model is correct and the unit is in good shape and
VSHFL¿FDWLRQDQGTXDQWLW\RIDFFHVVRULHVDUHULJKW
‹
Correct handling route and method shall be decided to prevent damage to the unit. For protecting the
unit and ensuring its safety, carrying the unit with its package is recommended. If such carrying method is
GLI¿FXOWXQGHUSDUWLFXODUFRQGLWLRQVWKHFDQWRQVKDOOQRWEHUHPRYHGWRDYRLGORRVHQHVVRUIDOOLQJGXULQJ
handling.
‹ Confirm the foundation is secure. When the unit is installed on the metal part of a building, electrical
insulation must be in compliance with relevant standards.
‹
&RQ¿UPWKHLQVWDOODWLRQSRVLWLRQLVDZD\IURPVWRUDJH]RQHRILQÀDPPDEOHDQGH[SORVLYHVXEVWDQFHVRU
RWKHUZLVHOHDNDJHRILQÀDPPDEOHDQGH[SORVLYHVXEVWDQFHVPD\OHDGWRH[SORVLRQRUD¿UH
2.2 Installation Site
‹
To ensure the unit in proper function, selection of installation location must be in accordance with following
principles:
‹ 2XWGRRUXQLWVKDOOEHLQVWDOOHGVRWKDWWKHDLUGLVFKDUJHGE\RXWGRRUXQLWZLOOQRWUHWXUQDQGWKDWVXI¿FLHQW
space for repair shall be provided around the unit.
‹ The installation site must have good ventilation, so that the outdoor unit can take in and exhaust enough
air. Ensure that there is no obstacle for the air intake and exhaust of the outdoor unit. If there is any
obstacle blocking the air intake or exhaust, remove it.
‹ Place of installation shall be strong enough to support the weight of outdoor unit, and it shall be able
to insulate noise and prevent vibration. Ensure that the wind and noise from the unit will not affect your
neighbors.
‹ Avoid direct sunshine over the unit. It is better to set up a sun shield as the protection.
‹ Place of installation must be able to drain the rainwater and defrosting water.
‹ Place of installation must ensure the unit will not be buried under snow or subject to the influence of
rubbish or oil fog.
‹ The installation site must be at a place where the air exhaust outlet does not face strong wind.
‹ Outdoor unit should be hoisted through indicated hoisting holes. During hoisting, special attention must be
paid to the unit to prevent collision into its sheet metal parts to avoid rust.
‹
Rubber cushion or spring shock absorber shall be used for outdoor unit to avoid excessive noise and
vibration.
‹ Rubber cushion or spring shock absorber shall be used for outdoor unit to avoid excessive noise and
vibration.
‹ Only professional personnel are allowed for unit installation.
2.3 Caution for Installation
‹ ,QVWDOODWLRQRIRXWGRRUXQLWVKDOOQRWDOORZGLVFKDUJHGDLUWRUHWXUQDQGVXI¿FLHQWPDLQWHQDQFHVSDFHVKDOOEHOHIW
around the unit.
‹ Installation position must be well-ventilated, enabling the unit to absorb and discharge enough air. Inlet and outlet
must be free of obstruction. Any obstacle blocking air going in and out must be removed.
‹ :KHQRXWGRRUXQLWLVPRXQWHGRQWKHVHFXUHÀRRUVXFKDVFRQFUHWHEROWVDQGQXWVLQ0FDQXVHGIRU¿[LQJWKHXQLW
Uprightness or levelness of the unit must be ensured.
‹ Outdoor unit should be hoisted through indicated hoisting holes. During hoisting, special attention must be paid to the
unit to prevent collision into its sheet metal parts to avoid rust.
‹ Rubber cushion or spring shock absorber shall be used for outdoor unit to avoid excessive noise and vibration.
Uprightness or levelness must be ensured.
‹ In installation of drain pipe, the connector of the drain pipe shall be inserted into a drain hole on the chassis of the
outdoor unit. And then a drain pipe shall be connected to the drain connector. (If the drain connector is used, installing
height of the outdoor unit shall be at least 5cm).