VESPA PX 125 150 euro 2 Скачать руководство пользователя страница 54

Страница: 54 / 142

Refitting the stator

In order to guarantee the correct engine timing pay

attention to the position of the stator, as shown in

the figure.

Flywheel and starting

Removing the starter motor

−

Remove the two screws and detach the drive box

from the starter motor.

−

With the aid of a hacksaw, abrade the pinion

head ring.

−

Using two screwdrivers, detach the cap.

−

Remove the retaining ring shown by the arrow in

the figure and remove the pinion components.

WARNING

THE PACKING ON THE MATING SURFACE MUST AL-
WAYS BE REPLACED WITH A NEW ONE, USING «LOC-
TITE».

Engine

Vespa PX 125 150 Euro 2

ENG - 54

Содержание PX 125 150 euro 2















































































































































Результаты поиска

Содержание PX 125 150 euro 2

Отзывы:

Похожие инструкции для PX 125 150 euro 2

Бренды по названию

Популярные бренды

VESPA PX 125 150 euro 2, Руководство по ремонту

Результаты поиска

Содержание PX 125 150 euro 2

Отзывы:

Похожие инструкции для PX 125 150 euro 2

Бренды по названию

Популярные бренды