VESPA LX 50 4V Скачать руководство пользователя страница 20

Страница: 20 / 76

02_01

Checks (02_01)

Before using the vehicle, check:

that the fuel tank is full.

The oil level in the rear hub.

engine oil level (see section «Engine oil level»).

That tyres are properly inflated.

correct functioning of headlights, rear taillight and turn indicators.

The correct functioning of the front and rear brakes.

02_02

Refuelling (02_02)

Fill fuel tank«

» with unleaded petrol (minimum octane rating = 95).

When the fuel reaches the reserve level, the warning light fitted on the instrument
panel lights up.

CAUTION

SHUT OFF THE ENGINE BEFORE REFUELLING WITH PETROL. PETROL IS
HIGHLY FLAMMABLE. DO NOT LET PETROL SPILL FROM THE TANK OR WHILE
REFUELLING

CAUTION

DO NOT BRING NAKED FLAMES OR CIGARETTES NEAR THE MOUTH OF THE
FUEL TANK: FIRE HAZARD. ALSO AVOID INHALING HARMFUL VAPOURS.

2 Use

Содержание LX 50 4V













































































Результаты поиска

Содержание LX 50 4V

Отзывы:

Похожие инструкции для LX 50 4V

Бренды по названию

Популярные бренды

VESPA LX 50 4V, Руководство пользователя

Результаты поиска

Содержание LX 50 4V

Отзывы:

Похожие инструкции для LX 50 4V

Бренды по названию

Популярные бренды